- 您现在的位置：买卖IC网 > PDF目录16433 > KIT33972AEWEVBE (Freescale Semiconductor)KIT EVALUATION FOR MC33972 PDF资料下载
参数资料
| 型号： | KIT33972AEWEVBE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR MC33972 |
| 标准包装： | 1 |
| 主要目的： | 接口，开关探测 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC33972 |
| 主要属性： | 8 可编程输入（电池开关或接地开关） |
| 次要属性： | 14 开关至接地输入 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
33972
TYPICAL APPLICATIONS
INTRODUCTION
from first device is connected to SI of second device). With
two devices, 48 clock pulses are required to shift data in.
When the WAKE feature is used to enable the power supply,
both WAKE pins should be connected to the enable pin on the
power supply. The INT pins may be connected to one
interrupt pin on the MCU or may have their own dedicated
interrupt to the MCU.
The transition from Normal to Sleep mode is done by
sending the sleep command. With the devices connected in
serial and the sleep command sent, both will enter Sleep
mode on the rising edge of CS. When Sleep mode is entered,
the WAKE pin will be logic [1]. If either device wakes up, the
WAKE
pin will transition LOW, waking the other device.
A condition exists where the MCU is sending the sleep
command (CS logic [0]) and a switch input changes state.
With this event the device that detects this input will not
transition to Sleep mode, while the second device will enter
Sleep mode. In this case two switch status commands must
be sent to receive accurate switch status data. The first
switch status command will wake the device in Sleep mode.
Switch status data may not be valid from the first switch
status command because of the time required for the input
voltage to rise above the 4.0 V input comparator threshold.
This time is dependant on the impedance of SGn or SPn
node. The second switch status command will provide
accurate switch status information. It is recommended that
software wait 10 to 20 ms between the two switch status
commands, allowing time for switch input voltages to
stabilize. With all switch states acknowledged by the MCU,
the sleep sequence may be initiated. All parameters for Sleep
mode should be updated prior to sending the sleep
command.
The 33972 IC has an internal 5.0 V supply from the VPWR
pin. A POR circuit monitors the internal 5.0 V supply. In the
event of transients on the VPWR pin, an internal reset may
occur. Upon reset the 33972 will enter Normal mode with the
internal registers as defined in Table 15, page 18. Therefore
it is recommended that the MCU periodically update all
registers internal to the IC.
USING THE WAKE FEATURE
The 33972 provides a WAKE output and wake-up input
designed to control an enable pin on system power supply.
While in the Normal mode, the WAKE output is LOW,
enabling the power supply. In the Sleep mode, the WAKE pin
is high, disabling the power supply. The WAKE pin has a
passive pull-up to the internal 5.0 V supply but may be pulled
When the WAKE output is not used, the pin should be
pulled up to the VDD supply through a resistor as shown in
During the Sleep mode, a switch closure will set the WAKE
pin LOW, causing the 33972 to enter the Normal mode. The
power supply will then be activated, supplying power to the
VDD pin and the microprocessor and the 33972. The
microprocessor can determine the source of the wake-up by
reading the interrupt flag.
COST AND FLEXIBILITY
Systems requiring a significant number of switch
interfaces have many discrete components. Discrete
components on standard PWB consume board space and
must be checked for solder joint integrity. An integrated
approach reduces solder joints, consumes less board space,
and offers wider operating voltage, analog interface
capability, and greater interfacing flexibility.
相关PDF资料 |
PDF描述 |
|---|---|
| EBM31DCMS | CONN EDGECARD 62POS .156 WW |
| VI-J1L-EX | CONVERTER MOD DC/DC 28V 75W |
| XR16V598IQ-0B-EVB | EVAL BOARD FOR XR16V598-A 100QFP |
| CM322522-820KL | INDUCTOR 82UH 60MA SMD |
| VI-2V2-EX | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33975AEWEVBE | 功能描述:交换机 IC 开发工具 MULTIPLE SWITCH DETECT I RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V |
| KIT33982CEVBE | 功能描述:电源管理IC开发工具 2.0 M HIGH-SIDE SW RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33982PNAEVB | 功能描述:电源管理IC开发工具 SPSS HIGH-SIDE SWTCH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33984CEVBE | 功能描述:电源管理IC开发工具 4.0 M HIGH-SIDE SW RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33984PNAEVB | 功能描述:电源管理IC开发工具 33984 - SPD4 EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。