参数资料
| 型号： | ISL28138FBZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP SGL/DUAL 4.5MHZ 8-SOIC |
| 标准包装： | 1,000 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 4.8 V/µs |
| 增益带宽积： | 4.5MHz |
| -3db带宽： | 13MHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 6µV |
| 电流 - 电源： | 900µA |
| 电流 - 输出 / 通道： | 75mA |
| 电压 - 电源，单路/双路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
12
FN6336.2
February 19, 2008
Rail-to-Rail Output
A pair of complementary MOS devices are used to achieve
the rail-to-rail output swing. The NMOS sinks current to
swing the output in the negative direction. The PMOS
sources current to swing the output in the positive direction.
The ISL28138 and ISL28238 with a 100k
Ω load will swing to
within 3mV of the positive supply rail and within 3mV of the
negative supply rail.
Results of Over-Driving the Output
Caution should be used when over-driving the output for long
periods of time. Over-driving the output can occur in two ways.
1) The input voltage times the gain of the amplifier exceeds the
supply voltage by a large value or, 2) the output current
required is higher than the output stage can deliver. These
conditions can result in a shift in the Input Offset Voltage (VOS)
as much as 1V/hr. of exposure under these conditions.
IN+ and IN- Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. They also contain
back-to-back diodes across the input terminals (see “Pin
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input
currents never exceed 5mA (Figure 42).
Enable/Disable Feature
The ISL28138 offers an EN pin that disables the device
when pulled up to at least 2.0V. In the disabled state (output
in a high impedance state), the part consumes typically 10A
at room temperature. By disabling the part, multiple
ISL28138 parts can be connected together as a MUX. In this
configuration, the outputs are tied together in parallel and a
channel can be selected by the EN pin. The loading effects
of the feedback resistors of the disabled amplifier must be
considered when multiple amplifier outputs are connected
together. Note that feed through from the IN+ to IN- pins
occurs on any Mux Amp disabled channel where the input
differential voltage exceeds 0.5V (e.g., active channel
VOUT = 1V, while disabled channel VIN = GND), so the mux
implementation is best suited for small signal applications. If
large signals are required, use series IN+ resistors, or large
value RF, to keep the feed through current low enough to
minimize the impact on the active channel. See “Limitations
details.The EN pin also has an internal pull-down. If left
open, the EN pin will pull to the negative rail and the device
will be enabled by default. When not used, the EN pin should
either be left floating or connected directly to the V- pin.
Limitations of the Differential Input Protection
If the input differential voltage is expected to exceed 0.5V, an
external current limiting resistor must be used to ensure the
input current never exceeds 5mA. For non-inverting unity gain
applications the current limiting can be via a series IN+ resistor,
or via a feedback resistor of appropriate value. For other gain
configurations, the series IN+ resistor is the best choice, unless
the feedback (RF) and gain setting (RG) resistors are both
sufficiently large to limit the input current to 5mA.
Large differential input voltages can arise from several
sources:
1) During open loop (comparator) operation. Used this way,
the IN+ and IN- voltages don’t track, so differentials arise.
2) When the amplifier is disabled but an input signal is still
present. An RL or RG to GND keeps the IN- at GND, while
the varying IN+ signal creates a differential voltage. Mux
Amp applications are similar, except that the active channel
VOUT determines the voltage on the IN- terminal.
3) When the slew rate of the input pulse is considerably
faster than the op amp’s slew rate. If the VOUT can’t keep up
with the IN+ signal, a differential voltage results, and visible
distortion occurs on the input and output signals. To avoid
this issue, keep the input slew rate below 4.8V/s, or use
appropriate current limiting resistors.
Large (>2V) differential input voltages can also cause an
increase in disabled ICC.
Using Only One Channel
If the application only requires one channel of the ISL28238,
the user must configure the unused channel to prevent it
from oscillating. The unused channel will oscillate if the input
and output pins are floating. This will result in higher than
expected supply currents and possible noise injection into
the channel being used. The proper way to prevent this
oscillation is to short the output to the negative input and
ground the positive input (as shown in Figure 43).
FIGURE 42. INPUT CURRENT LIMITING
-
+
RIN
RL
VIN
VOUT
FIGURE 43. PREVENTING OSCILLATIONS IN UNUSED
CHANNELS
-
+
ISL28138, ISL28238
相关PDF资料 |
PDF描述 |
|---|---|
| 147102-6 | CONN RCPT 12POS .100 DUAL SMD |
| VC060318A400DP | VARISTOR TVS 18VDC 30A 0603 |
| AS168X-CB2H070 | CIRCUIT BRKR THERMAL 7.0A 2POLE |
| EL5251IYZ-T13 | IC VFA 200MHZ DUAL 8-MSOP |
| 8-100400-4 | MICRO-MATCH FSID NP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28138FHZ-T7 | 功能描述:IC OPAMP SGL/DUAL 4.5MHZ SOT23-6 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| ISL28138FHZ-T7A | 功能描述:IC OPAMP SGL RRIO 4.5MHZ SOT23-6 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| ISL28138FHZ-TZA | 制造商:Intersil Corporation 功能描述: |
| ISL28146 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:5MHz, Single and Dual Rail-to-Rail Input-Output (RRIO) Op Amps |
| ISL28146_0806 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:5MHz, Single and Dual Rail-to-Rail Input-Output (RRIO) Op Amps |
发布紧急采购，3分钟左右您将得到回复。