- 您现在的位置：买卖IC网 > PDF目录17734 > IS-L0102-IS15ABCP4CF (NKK Switches)BOARD LOGIC IS15ABCP4CF & AT548 PDF资料下载
参数资料
| 型号： | IS-L0102-IS15ABCP4CF |
| 厂商： | NKK Switches |
| 文件页数： | 7/52页 |
| 文件大小： | 0K |
| 描述： | BOARD LOGIC IS15ABCP4CF & AT548 |
| RoHS指令信息： | AT, IS Series, Cert of Compliance |
| 标准包装： | 1 |
| 附件类型： | 逻辑板 |
| 适用于相关产品： | Standard SmartSwitch? |
| 配用： | 360-2330-ND - SMARTSWITCH STD RED/GRN LED |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
IS-C1603 Intelligent Controller User
Manual
7850 East Gelding Drive ? Scottsdale, AZ 85260-3420
E.
If bit 5 of FLAG-A is enabled (default: enabled) and bit 2 of FLAG-B is zero (default: 0) then do the
following:
E1. If the viewing angle/brightness code is not zero, then increase or decrease the brightness
accordingly.
E2. Update the switches’ image addresses with the Addresses from the Attribute Block. If any of the
Addresses in the attribute block is equal to zero do not change that switch’s image address.
E3. If bit 0 of FLAG-B is enabled (default: enabled), update the LCD/LED codes for the switches
according to data from updated switch image addresses.
Commands from host:
There are many commands available for the host to control the switches in real-time or set up the controller for
stand-alone operation. The commands are described in proceeding section.
5. Data formats
This section describes the definitions and data block formats.
5.1 Key Terms & Definitions
Byte
Nibble/Hex digit
ASCII
Communication
An eight bit hex value ranging from 00H to FFH (Decimal 0 to 255). The bit
format of a byte is: (B7 B6 B5 B4 B3 B2 B1 B0) where B7 is most significant
and bit B0 is least significant bit.
A four bit value ranging from 0H to FH. A byte consists of two nibbles.
A byte value representing a symbol.
There are two formats to transmit a byte:
Format
1. Hex format - A hex byte is transmitted without any change to it. [ xxH ] will
be used to denote this.
For example, the hex byte 5AH is transmitted as a single byte 5AH.
All commands and some data are sent using this format.
2. ASCII HEX format - Each nibble of the byte is converted to ASCII code
and sent as a byte. [ xxAH ] will be used to denote this.
For example, the hex byte 5AH is transmitted in two bytes, 35H and 41H .
The ASCII value for 5 is 35H and the ASCII value for A is 41H .
All addresses and most data are sent using this format.
IS-C1603 Intelligent Controller User Manual D.doc
Toll Free 1.877.2BUYNKK (877.228.9655) ? Phone 480.991.0942 ? Fax 480.998.1435
www.nkkswitches.com ? Email engineering@nkkswitches.com
Page 7 of 52
0110
相关PDF资料 |
PDF描述 |
|---|---|
| CPPLC5-LT56T | OSC 3.3V PROG CMOS TRI ST 100PPM |
| CPPLC5-LT56P | OSC 3.3V PROG CMOS PWRDN 100PPM |
| CPPLC5-LT0PT | OSC 3.3V PROG CMOS TRI ST 50PPM |
| AB15AV | SWITCH PUSH SPDT 0.4VA 28V |
| AB11AB1-FA | SWITCH PUSH SPST-NO 0.4VA 28V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS-L0106-IS15ABFP4RGB | 功能描述:按钮开关 PROGRAMMABLE SWITCH RoHS:否 制造商:C&K Components 触点形式:2 NC - 2 NO 开关功能:ON ? OFF 电流额定值:4 A 电压额定值 AC:12 V to 250 V 电压额定值 DC:12 V to 50 V 功率额定值: 安装风格:Through Hole 照明:Illuminated 照明颜色:None IP 等级:IP 40 端接类型:Solder 触点电镀:Silver 执行器:Square 盖颜色: 封装: 可燃性等级:UL 94 V-0 |
| IS-L0107-IS15ABFP4RGB | 功能描述:交换机开发工具 IS15ABFP4RGB w/Logic AT548 Panel Mt Hous RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| IS-L0204-C | 功能描述:交换机开发工具 Logic Board with 2 Standard RGB Sockets RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| IS-L0205-C | 功能描述:交换机开发工具 Logic Board for two LCD 36X24 RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| IS-L0251-C | 功能描述:交换机开发工具 Logic Board with 2 Stndrd Display Sckts RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。