- 您现在的位置：买卖IC网 > PDF目录18734 > EM260-RTY (Silicon Laboratories Inc)IC ZIGBEE SYSTEM-ON-CHIP 40-QFN PDF资料下载
参数资料
| 型号： | EM260-RTY |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 29/50页 |
| 文件大小： | 0K |
| 描述： | IC ZIGBEE SYSTEM-ON-CHIP 40-QFN |
| 标准包装： | 429 |
| 频率： | 2.4GHz |
| 数据传输率 - 最大： | 250kbps |
| 调制或协议： | 802.15.4 |
| 应用： | ZigBee? |
| 功率 - 输出： | -32dBm ~ 3dBm |
| 灵敏度： | -97dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 30mA |
| 电流 - 传输： | 34mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 托盘 |
| 其它名称： | 636-1003 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
EM260
When the EM260 resets, it will assert the nHOST_INT signal, telling the Host that it has data. The Host should
request data from the EM260 as usual. The EM260 will ignore whatever command is sent to it and respond only
with two bytes. The first byte will always be 0x00 and the second byte will be the reset type as defined by
EmberResetType . This specialty SPI Byte is never used in another Response SPI Byte. If the Host sees 0x00
from the EM260, it knows that the EM260 has been reset. The EM260 will deassert the nHOST_INT signal
shortly after receiving a byte on the SPI and process all further commands in the usual manner. In addition to
the Host having control of the reset line of the EM260, the EmberZNet Serial Protocol also provides a
mechanism for a software reboot.
5.6.1
Bootloading the EM260
The SPI Protocol supports a Payload Frame called the Bootloader Frame for communicating with the EM260
when the EM260 is in bootloader mode. The EM260 can enter bootload mode through either an EZSP command
or holding one of two pins low while the EM260 exits reset. Both the nWAKE pin and the PTI_DATA pin are
capable of activating the bootloader while performing a standard EM260 reset procedure. Assert nRESET to
hold the EM260 in reset. While nRESET is asserted, assert (active low) either nWAKE or PTI_DATA and then
deassert nRESET to boot the EM260. Do not deassert nWAKE or PTI_DATA until the EM260 asserts nHOST_INT,
indicating that the EM260 has fully booted and is ready to accept data over the SPI Protocol. Once nHOST_INT
is asserted, nWAKE or PTI_DATA way be deasserted. Refer to document UG103.6, Ember Application
Development Fundamentals: Bootloading , for more information on the bootloader and the format of the
Bootloader Frame.
5.6.2
Unexpected Resets
The EM260 is designed to protect itself against undefined behavior due to unexpected resets. The protection is
based on the state of Slave Select since the inter-command spacing mandates that Slave Select must return to
idle. The EM260’s internal SPI Protocol uses Slave Select returning to idle as a trigger to reinitialize its SPI
Protocol. By always reinitializing, the EM260 is protected against the Host unexpectedly resetting or
terminating a transaction. Additionally, if Slave Select is active when the EM260 powers on, the EM260 will
ignore SPI data until Slave Select returns to idle. By ignoring SPI traffic until idle, the EM260 will not begin
receiving in the middle of a transaction.
If the Host resets, in most cases it should reset the EM260 as well so that both devices are once again in the
same state: freshly booted. Alternately, the Host can attempt to recover from the reset by recovering its
previous state and resynchronizing with the state of the EM260.
If the EM260 resets during a transaction, the Host can expect either a Wait Section timeout or a missing Frame
Terminator indicating an invalid Response.
If the EM260 resets outside of a transaction, the Host should proceed normally.
5.7
Transaction Examples
This section contains the following transaction examples:
SPI Protocol Version
EmberZNet Serial Protocol Frame-Version Command
EM260 Reset
Three-Part Transaction: Wake, Get Version, Stack Status Callback
Page 29
120-0260-000M Rev 1.1
相关PDF资料 |
PDF描述 |
|---|---|
| DP1205C915 | MODULE DROP IN FOR XE1205 915MHZ |
| DP1205C868 | MODULE DROP IN FOR XE1205 868MHZ |
| DP1205C433 | MODULE DROP IN FOR XE1205 433MHZ |
| LP0603A1747ANTR | FILTER LOW PASS 1747MHZ 0603 SMD |
| DP1203C9153LF | MODULE DROP IN FOR XE1203 915MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EM260-USART-JMP-R | 功能描述:KIT JUMP START FOR EM260 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:JumpStart 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| EM2630-12# | 制造商:Fluke Electronics 功能描述:BNC (F) TO ALLIGATOR CLIPS 12 INCHES 制造商:Pomona Electronics 功能描述: |
| EM-26392-C36 | 功能描述:麦克风 3.61 X 3.61 X 2.21MM -51 SENS, 12SL PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作电压:0.9 V to 10 V 灵敏度:- 53 dB 端接类型:Wire Leads 长度:5.56 mm 宽度:3.98 mm 深度:2.21 mm |
| EM-26596-C36 | 功能描述:麦克风 3.61 X 3.61 X 2.21MM -52 SENS, 12B PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作电压:0.9 V to 10 V 灵敏度:- 53 dB 端接类型:Wire Leads 长度:5.56 mm 宽度:3.98 mm 深度:2.21 mm |
| EM-26596-D58 | 功能描述:麦克风 3.61 X 3.61 X 2.21MM -52 SENS, 12B PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作电压:0.9 V to 10 V 灵敏度:- 53 dB 端接类型:Wire Leads 长度:5.56 mm 宽度:3.98 mm 深度:2.21 mm |
发布紧急采购，3分钟左右您将得到回复。