参数资料
| 型号： | EL2480CSZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 2/13页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP QUAD 250MHZ/3MA 14-SOIC |
| 标准包装： | 1,000 |
| 放大器类型： | 电流反馈 |
| 电路数： | 4 |
| 转换速率： | 1200 V/µs |
| -3db带宽： | 250MHz |
| 电流 - 输入偏压： | 16µA |
| 电压 - 输入偏移： | 2500µV |
| 电流 - 电源： | 3mA |
| 电流 - 输出 / 通道： | 55mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 12 V，±1.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
10
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same
frequency response as DC levels are changed at the output.
This is especially difficult when driving a standard video load
of 150
, because of the change in output current with DC
level. Until the EL2480, good Differential Gain could only be
achieved by running high idle currents through the output
transistors (to reduce variations in output impedance). These
currents were typically comparable to the entire 3mA supply
current of EL2480 amplifier! Special circuitry has been
incorporated in the EL2480 to reduce the variation of output
impedance with current output. This results in dG and dP
specifications of 0.05% and 0.05° while driving 150
at a
gain of +2.
Video performance has also been measured with a 500
load at a gain of +1. Under these conditions, the EL2480 has
dG and dP specifications of 0.01% and 0.01° respectively
while driving 500
at AV = +1.
Output Drive Capability
This amplifier of the EL2480 is capable of providing a
minimum of ±50mA. These output drive levels are
unprecedented in amplifiers running at these supply currents.
The ±50mA minimum output drive of the EL2480 amplifier
allows swings of ±2.5V into 50
loads.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will decouple
the EL2480 from the cable and allow extensive capacitive
drive. However, other applications may have high capacitive
loads without a back-termination resistor. In these
applications, a small series resistor (usually between 5
and
50
) can be placed in series with the output to eliminate most
peaking. The gain resistor (RG) can then be chosen to make
up for any gain loss which may be created by this additional
resistor at the output. In many cases it is also possible to
simply increase the value of the feedback resistor (RF) to
reduce the peaking.
Current Limiting
The EL2480 has no internal current-limiting circuitry. If any
output is shorted, it is possible to exceed the Absolute
Maximum Ratings for output current or power dissipation,
potentially resulting in the destruction of the device.
Power Dissipation
With the high output drive capability of the EL2480, it is
possible to exceed the 150°C Absolute Maximum junction
temperature under certain very high load current conditions.
Generally speaking, when RL falls below about 25, it is
important to calculate the maximum junction temperature
(TJMAX) for the application to determine if power-supply
voltages, load conditions, or package type need to be
modified for the EL2480 to remain in the safe operating area.
These parameters are calculated as follows:
where:
TMAX = Maximum ambient temperature
θ
JA = Thermal resistance of the package
n = Number of amplifiers in the package
PDMAX = Maximum power dissipation of each amplifier in
the package
PDMAX for each amplifier can be calculated as follows:
where:
VS = Supply voltage
ISMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage of the application
RL = Load resistance
T
JMAX
T
MAX
Θ
JA
nPD
MAX
×
()
+
=
PD
MAX
2
(
V
S
I
SMAX )
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
EL2480
相关PDF资料 |
PDF描述 |
|---|---|
| EL5251ISZ-T7 | IC VFA 200MHZ DUAL 8-SOIC |
| 5-102084-7 | CONN RCPT 18POS DUAL R/A T/H |
| VC080512A250DP | VARISTOR TVS 12VDC 40A 0805 |
| 1-535541-5 | CONN RCPT 17POS .100 GOLD |
| 0459851383 | CONN HEADER 10PWR 40SGL 1.57MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL2480-EVM | 制造商:Intersil Corporation 功能描述:250MHz/3mA Current Mode Feedback Amplifier 制造商:P&S 功能描述:250MHz/3mA Current Mode Feedback Amplifier |
| EL25-1/2-ADUL | 制造商:Fuji Electric 功能描述: |
| EL-25-21/W1D-ANQHY/2A | 功能描述:标准LED-SMD Pure White InGaN Yellow Diffused Lens RoHS:否 制造商:Vishay Semiconductors 封装 / 箱体:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明颜色:Red 波长/色温:631 nm 透镜颜色/类型:Water Clear 正向电流:30 mA 正向电压:2 V 光强度:54 mcd 显示角:130 deg 系列:VLMx1500 封装:Reel |
| EL-25-21SURC/S530-A2/TR8 | 功能描述:标准LED-SMD Red Water Clear 624nm 44mcd RoHS:否 制造商:Vishay Semiconductors 封装 / 箱体:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明颜色:Red 波长/色温:631 nm 透镜颜色/类型:Water Clear 正向电流:30 mA 正向电压:2 V 光强度:54 mcd 显示角:130 deg 系列:VLMx1500 封装:Reel |
| EL-25-21UBC/C430/TR8 | 功能描述:标准LED-SMD Blue Water Clear 466nm 20mcd RoHS:否 制造商:Vishay Semiconductors 封装 / 箱体:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明颜色:Red 波长/色温:631 nm 透镜颜色/类型:Water Clear 正向电流:30 mA 正向电压:2 V 光强度:54 mcd 显示角:130 deg 系列:VLMx1500 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。