- 您现在的位置：买卖IC网 > Datasheet目录620 > CUB7T000 (Red Lion Controls)TIMER LCD PROGRAM 8 DIGIT Datasheet资料下载
参数资料
| 型号： | CUB7T000 |
| 厂商： | Red Lion Controls |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TIMER LCD PROGRAM 8 DIGIT |
| 标准包装： | 1 |
| 系列： | CUB7 |
| 工作模式： | 累积 |
| 输出类型： | 无 |
| 电源电压： | 不需要（包括电池） |
| 端接类型： | 螺丝端子 |
| 显示器类型： | LCD 无背光 |
| 其它名称： | RLC7T0 |
IEC-61010-1, EN 61010-1: Safety requirements for electrical equipment
for measurement, control, and laboratory use, Part 1.
IP65 Enclosure rating (Face only), IEC 529
ELECTROMAGNETIC COMPATIBILITY
Immunity to EN 50082-2
Electrostatic discharge EN 61000-4-2 Level 2; 4 Kv contact
Level 3; 8 Kv air
INSTALLATION
The CUB7T meets NEMA 4X/IP65 requirements for indoor use when
properly installed. The units are intended to be mounted into an enclosed
panel. The viewing window and reset button are factory sealed for a
washdown environment. A sponge rubber gasket and mounting clip are
provided for installing the unit in the panel cut-out.
Electromagnetic RF fields
Fast transients (burst)
RF conducted interference
Simulation of cordless telephone
EN 61000-4-3
EN 61000-4-4
EN 61000-4-6
ENV 50204
Level 3; 10 V/m
80 MHz - 1 GHz
Level 4; 2 Kv I/O
Level 3; 2 Kv power 1
Level 3; 10 V/rms
150 KHz - 80 MHz
Level 3; 10 V/m
900 MHz ± 5 MHz
200 Hz, 50% duty cycle
Installation Environment
The unit should be installed in a location that does not exceed the
maximum operating temperature and provides good air circulation. Placing
the unit near devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and neutral soap
product. Do NOT use solvents.
Continuous exposure to direct sunlight may accelerate the aging process of
the bezel.
Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate
the push buttons of the unit.
Emissions to EN 50081-1
RF interference
EN 55022
Enclosure class B
Notes
1. Backlit powered units require a power line filter to be installed,
RLC LFIL0000 or equivalent, so as not to impair the function of the
backlighting.
Refer to EMC Installation Guidelines for additional information.
11. CONSTRUCTION : High impact plastic case with clear viewing window.
EXISTING
PANEL
0.05" to 0.20"
(1.3 to 5.1 mm)
THICK
LATCHING
FEATURE
3-R
EN
1-C
5-R
LS
+V
HS
The front panel meets NEMA 4X/IP65 requirements for indoor use when
properly installed. Installation Category I, Pollution Degree 2. Panel gasket
and mounting clip included.
12. WEIGHT : 2 oz. (57 grams) [with battery]
MOUNTING
SCREW
ST
OM
ST
-4
-2
-6
BEZEL
GASKET
TIMER RANGE SELECTION
The CUB7T’s timer range can be modified in the Program mode. The
Program mode uses the PGM button (refer to photo) to switch between
Program and Operate modes. The RESET button (refer to photo) is used to
select the desired timer range.
Note: Timer range and accumulated time on the display will be lost if the
battery is removed from the unit
ANNUNCIATOR
0.062"
(1.57 mm)
THICK
MOUNTING
CLIP
The following procedure assures proper installation:
1. Cut panel opening to specified dimensions. Remove burrs and clean
around panel opening.
2. Carefully remove and discard the center section of the gasket.
3. Slide the panel gasket over the rear of the counter body to the back of the
bezel. Install CUB7T unit through the panel cut-out.
4. Insert the mounting screws onto both sides of mounting clip. Tip of screw
should NOT project from hole in mounting clip.
5. Slide the mounting clip over the rear of the unit until the clip is against the
back of the panel. The mounting clip has latching features which engage
into mating features on the CUB7T housing.
PGM
RST
6. Note: It is necessary to hold the unit in place when sliding mounting clip
into position.
7. Alternately tighten each screw to ensure uniform gasket pressure.
Connect wires between RST EN (Reset Enable) and COM. (Common); and
between HS (Program Enable) and COM. (Common) to enable front push
buttons. Press the PGM button to enter Program Mode, allowing selection of
the desired timer range. The display will show 00000.000 (Timer Range 0.001
sec). Repeatedly pressing the RST button will cycle through the available timer
ranges as shown in the table.
When the desired timer range is
Visually inspect the front panel gasket. The gasket should be compressed
to about 75 to 80% of its original thickness. If not, gradually turn mounting
screws to further compress gasket.
8. If the gasket is not adequately compressed and the mounting screws can no
longer be turned, loosen mounting screws, and check that the mounting
clip is latched as close as possible to the panel.
9. Repeat from step #5 for tightening mounting screws.
displayed, press PGM to load the
range and return to operating
DISPLAY DURING
PROGRAMMING
Timer Range
mode. ( The CUB7T will remain
in Program Mode until the PGM
button is pressed. ) Remove the
wire from the HS (Program
Enable) terminal to prevent
accidental changes to the timer
range. Any new time accumulated
will be at the new rate selected.
Note: To avoid incorrect display
information, it is recommended
that the CUB7T be reset after
making programming changes.
00000.000
111111.11
2222222.2
33333333
4444444.4
55555555
666666.66
7777777.7
88888888
9999.99.99
0.001 Sec
0.01 Sec
0.1 Sec
1 Sec
0.1 Min
1 Min
0.01 Hr
0.1 Hr
1 Hr
Factory Use Only
TROUBLESHOOTING
For further technical assistance, contact technical support at the appropriate
company numbers listed.
2
相关PDF资料 |
PDF描述 |
|---|---|
| CUB7W020 | COUNTER 8-DIGIT RED BKLT VOLT-IN |
| D-659-0001 | TOOL REMOVAL MTC CONN WAFER |
| D7-1 | DIE, .041 HOLE DIA |
| DH2X61-18A | DIODE FST REC 1800V2X60A SOT227B |
| DHG100X1200NA | DIODE ARRAY 1200V 50A SOT227B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CUB7T100 | 功能描述:TIMER LCD PROGRAM V IN 8 DIGIT RoHS:是 类别:工业控制，仪表 >> 定时器 系列:CUB7 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| CUB7T120 | 制造商:Red Lion Controls 功能描述:ELECTRONIC TIMER VOLTAGE RED LCD |
| CUB7TCG0 | 功能描述:TIMER LCD PROGRAM 8-DIGIT LV GRN RoHS:是 类别:工业控制，仪表 >> 定时器 系列:CUB7 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| CUB7TCG1 | 制造商:Red Lion Controls 功能描述:TIMER SOURCE GREEN DISPLAY 8-DIGIT 制造商:Red Lion Controls 功能描述:TIMER LCD GREEN DIS .001S-1H PAN |
| CUB7TCR0 | 功能描述:TIMER LCD PROGRAM 8-DIGIT LV RED RoHS:是 类别:工业控制，仪表 >> 定时器 系列:CUB7 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
发布紧急采购，3分钟左右您将得到回复。