- 您现在的位置：买卖IC网 > Datasheet目录614 > BMK11000 (Red Lion Controls)OR MLPS DIN RAIL BASE MNT KIT AD Datasheet资料下载
参数资料
| 型号： | BMK11000 |
| 厂商： | Red Lion Controls |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | OR MLPS DIN RAIL BASE MNT KIT AD |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | RLC150 |
CUB5 INSTALLATION
1. Remove the panel latch (mounting clip) from the indicator. Insert the
indicator into the BMK11 per diagram at right. Verify indicator is fully
seated and latches have engaged. With latches properly engaged the
indicator will not pull out of the BMK11.
2. Wire the indicator.
3. For DIN RAIL mounting, insert the two plastic feet as shown in the diagram
at right. Angle the assembly so that the top groove of both rail feet are
located over the top lip of the rail. Rotate the assembly towards the rail until
it snaps into place.
4. To remove the assembly from the rail, place a screwdriver behind one of the
rail feet and draw the rail foot away from the rail disengaging it from the rail.
Apply the same procedure to the second rail foot and remove the complete
assembly from the rail.
5. For Base Mount , use the holes indicated in the diagram at right, and screw
or bolt the assembly to the desired mounting surface. User is responsible for
selecting the appropriate screw or bolt to provide mounting to the desired
surface. Base mount holes in the BMK11 are designed for #8 hardware.
6. To remove the indicator from the BMK11, slide a small screwdriver into the
slot provided in the latch. Draw the latch away from the indicator until
disengaged. Repeat the procedure on the other side. Once the latches are
released, remove the indicator from the BMK11.
MLPS INSTALLATION
1. Using the two nuts supplied with the BMK11, affix standoffs from MLPS
hardware pack as indicated in the diagram at left.
2. Snap the MLPS over the standoffs into the BMK11 as indicated in the diagram.
3. Attach the MLPS to the standoffs using the square washers and SEMS terminal
screws included with MLPS hardware pack.
4. Assembly can be wired at this time, or after the mounting is completed.
5. For DIN RAIL mounting, insert the two plastic feet as shown in the diagram.
Angle the assembly so that the top groove of both rail feet are located over the
top lip of the rail. Rotate the assembly towards the rail until it snaps into place.
6. For Base Mount , use the holes indicated in the diagram at left, and screw or
bolt the assembly to the desired mounting surface. User is responsible for
selecting the appropriate screw or bolt to provide mounting to the desired
surface. Base mount holes in BMK11 are designed for #8 hardware.
7. To remove the MLPS from the BMK11, slide a small screwdriver between the
MLPS and the latch wall. Draw the latch away from the MLPS until
disengaged. Repeat procedure on the other side. Once latches are released
remove the MLPS from the BMK11.
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years
from the date of shipment, provided the products have been stored, handled, installed, and used under proper conditions. The
Company’s liability under this limited warranty shall extend only to the repair or replacement of a defective product, at The
Company’s option. The Company disclaims all liability for any affirmation, promise or representation with respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against damages, claims, and expenses
arising out of subsequent sales of RLC products or products containing components manufactured by RLC and based upon personal
injuries, deaths, property damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be to
any extent liable, including without limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and liability
imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those expressly contained herein.
The Customer acknowledges the disclaimers and limitations contained herein and relies on no other warranties or affirmations.
Red Lion Controls AP
Red Lion Controls
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Red Lion Controls BV
Printerweg 10
NL - 3821 AD Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
Unit 101, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel +86 21 6113-3688
Fax +86 21 6113-3683
相关PDF资料 |
PDF描述 |
|---|---|
| BMK70000 | BASE MOUNT KIT CUB4/DT8 W/MLPS |
| C1435ALMAA | TEMP MONITOR LOG PNL MNT |
| C200H-ATTA3 | I/O LOCK BRACKT 10-SLOT |
| C200H-PID03 | PID MODULE CURRENT OUT |
| CAT-EX-169-01 | EXTRACTION TOOL FOR C-169 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BMK1A000 | 制造商:Red Lion Controls 功能描述:BASE MOUNT KIT CUB 1 制造商:Red Lion Controls 功能描述:CUB 1 BASE MOUNT KIT |
| BMK20000 | 制造商:Red Lion Controls 功能描述:BASE MOUNT KIT CUB 2 制造商:Red Lion Controls 功能描述:CUB 2 BASE MOUNT KIT |
| BMK30000 | 制造商:Red Lion Controls 功能描述:BASE MOUNT KIT FOR LEGEND, LIBRA, LYNX, T16, P16, T48, P48 & C48 制造商:Red Lion Controls 功能描述:1/16 DIN LIBRA AND LEGEND BASE |
| BMK40000 | 制造商:Red Lion Controls 功能描述:BASE MOUNT KIT APOLLO/GEMINI 制造商:Red Lion Controls 功能描述:1/8 DIN AND GEMINI BASE MOUNT |
| BMK50000 | 制造商:Red Lion Controls 功能描述:BASE MOUNT KIT CUB 3 制造商:Red Lion Controls 功能描述:CUB 3 BASE MOUNT KIT |
发布紧急采购，3分钟左右您将得到回复。