- 您现在的位置：买卖IC网 > PDF目录13239 > BD00KA5WF-E2 (Rohm Semiconductor)IC REG LDO ADJ .5A SOP8 PDF资料下载
参数资料
| 型号： | BD00KA5WF-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 10/18页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A SOP8 |
| 特色产品： | CMOS LDO Regulators |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1 V ~ 4 V |
| 输入电压： | 2.3 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.12V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA（最小值） |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1370 (CN2011-ZH PDF) |
| 其它名称： | BD00KA5WF-E2DKR |
BDxxKA5 Series BDxxKA5W Series
BD00KA5W Series
Datasheet
The calculation method for power consumption Pc(W) is as follows :
Pc = (Vcc-Vo)×Io+Vcc×Icca
Acceptable loss Pd ≧ Pc
Solving for the load current I O in order to operate within the acceptable loss,
Vcc ： Input voltage
Vo ： Output voltage
Io ： Load current
Icca ： Circuit current
Io ≦
Pc – Vcc×Icca
Vcc － Vo
It is then possible to find the maximum load current Io MAX with respect to the applied voltage Vcc at the time of thermal design.
Calculation Example
Example 1) When Ta=85 ℃ , Vcc=2.5V, Vo=1.0V
BA10KA5WFP （ TO252-5 packaging ）
Io ≦
0.676 － 2.5×Icca
2.5-1.0
Io ≦ 440mA (Icca : 6mA)
θ ja=96.2 ℃ /W → -10.4mW/ ℃
25 ℃ =1300mW → 85 ℃ =676mW
Please refer to the above information and keep thermal designs within the scope of acceptable loss for all operating
temperature ranges.
The power consumption Pc of the IC when there is a short circuit (short between Vo and GND) is :
Pc=Vcc×(Icca+Ishort)
*Ishort : Short circuit current
● Terminal Vicinity Settings and Cautions
? Vcc Terminal
Please attach a capacitor (greater than 1 μ F) between Vcc and GND.
The capacitance values differ depending on the application, so chose a capacitor with sufficient margin and verify the
operation on actual board.
? GND Terminal
Please be sure to keep the set ground and IC ground at the same potential level so that a potential difference does not
arise between them. If a potential difference arises between the set ground and the IC ground, the preset voltage will not
be output properly, causing the system to become unstable. Please reduce the impedance by making the ground patterns
as wide as possible and reducing the distance between the set ground and the IC ground as much as possible.
? CTL Terminal
CTL
31.25k ?
The CTL terminal is turned ON at 2.0V and higher, and OFF at
0.8V and lower, within the operating power supply voltage range.
The power supply and the CTL terminal may be started up and
shut down in any order without problems.
25k ?
Fig.23 Input equivalent circuit
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
10/15
TSZ02201-0R6R0A600150-1-2
26.Jun.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| MAX630CSA+T | IC REG BOOST 0.15A 8SOIC |
| VI-JWT-CY-S | CONVERTER MOD DC/DC 6.5V 50W |
| 450BXW39MEFC16X20 | CAP ALUM 39UF 450V 20% RADIAL |
| AMM12DRMN-S288 | CONN EDGECARD 24POS .156 EXTEND |
| VI-JWP-CY-S | CONVERTER MOD DC/DC 13.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD00KA5WFP | 制造商:ROHM 制造商全称:Rohm 功能描述:Low ESR Capacitor Built in shut down SW, Low Dropout 500mA Regulator IC |
| BD00KA5WFP-E2 | 功能描述:低压差稳压器 - LDO VARIABLE 1.0V-3.3V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BD01 | 功能描述:DIP 开关/ SIP 开关 STD PROFILE 1 POS RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole |
| BD01 | 制造商:C&K Components 功能描述:DIP SWITCH POSITION 1 |
| BD015-02 | 制造商:NVE Corporation 功能描述:ELECTRONIC COMPONENT |
发布紧急采购，3分钟左右您将得到回复。