参数资料
| 型号： | ADM00345 |
| 厂商： | Microchip Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 3PH BLDC CTLR MTD6505 |
| 设计资源： | ADM00345 Gerber File ADM00345 Schematic |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电机控制 |
| 嵌入式： | 是，MCU，16 位 |
| 已用 IC / 零件： | MTD6505 |
| 主要属性： | 3 相无刷 DC（BLDC）电机 |
| 次要属性： | 过压、短路和热保护 |
| 已供物品： | 板 |
| 相关产品： | MTD6505T-E/NATR-ND - IC BLDC MOTOR DVR 5V 3PH 10-UDFN MTD6505T-E/NADKR-ND - IC BLDC MOTOR DVR 5V 3PH 10-UDFN MTD6505T-E/NACT-ND - IC BLDC MOTOR DVR 5V 3PH 10-UDFN |
MTD6505
4.0
FUNCTIONAL DESCRIPTION
4.3
Frequency Generator Function
The MTD6505 generates a full-wave signal to drive a
3-phase BLDC motor. High efficiency and low-power
consumption are achieved due to CMOS transistors
and synchronous rectification drive type.
The Frequency Generator output (FG) is a “Hall-effect
sensor equivalent” digital output, giving information to
an external controller about the speed and phase of the
motor. The FG pin is an open drain output, connecting
to a logical voltage level through an external pull-up
4.1
Speed Control
resistor. When a lock, or an out-of-sync situation is
detected by the driver, this output is set to high-
The rotational speed of the motor can be controlled
either through the PWM digital input signal or by acting
directly on the power supply (V DD ). When the PWM
signal is High (or left open), the motor rotates at full
speed. When the PWM signal is low, the IC outputs are
set to high-impedance and the motor is stopped.
By changing the PWM duty cycle, the speed can be
adjusted. Thus, the user has maximum freedom to
choose the PWM system frequency within a wide range
(from 1 kHz to 100 kHz).
Since the PWM pin has an internal pull-up resistor
connected to V DD , it is recommended to drive it
between 0V and High-Z. The PWM driver must be able
to support the pull-up resistor current, in order to drive
the pin. See “PWM Internal Pull-Up Resistor” in
The output transistor activation always occurs at a fixed
rate of 30 kHz, which is outside of the range of audible
frequencies.
impedance until the motor is restarted. Leave the pin
open when it is not used.
4.4 Lockup Protection and Automatic
Restart
If the motor is blocked and cannot rotate freely, a lock-
up protection circuit detects it and disables the driver by
setting its outputs to high-impedance to prevent the
motor coil from burnout. After a “waiting time” (T WAIT ),
the lock-up protection is released and normal operation
resumes for a given time (T RUN ). If the motor is still
blocked, a new period of waiting time is started. T WAIT
and T RUN timings are fixed internally, so that no exter-
nal capacitor is required.
4.5 Overcurrent Protection
The motor peak current is limited by the driver to
750 mA (standard value), thus limiting the maximum
power dissipation in the coils.
Note 1: The PWM frequency has no direct affect
on the motor speed and is asynchronous
4.6
Thermal Shutdown
with the activation of the output
transistors.
Note 2: The standard output frequency is 30 kHz.
A 20 kHz output frequency option is
available upon request.
The MTD6505 device has a thermal protection function
which detects when the die temperature exceeds
T J = +170°C. When this temperature is reached, the
circuit enters the Thermal Shutdown mode, and the
outputs OUT1, OUT2 and OUT3 are disabled (high-
4.2
Motor Rotation Direction
impedance), avoiding the IC destruction and allowing
the circuit to cool down. When the junction temperature
The current-carrying order of the outputs depends on
the DIR pin state (“Rotation Direction”) and is described
in Table 4-1 . The DIR pin is not designed for dynamic
direction change during operation.
(T J ) drops below +145°C, normal operation resumes.
The thermal detection circuit has +25°C hysteresis.
Thermal shutdown
TABLE 4-1:
MOTOR ROTATION
DIRECTION OPTIONS
(DIR PIN)
Normal
DIR Pin State
Connected
Rotation
Direction
Forward
Outputs Activation
Sequence
OUT1 ? OUT2 ? OUT3
operation
+145°
+170°
T J
to GND
or Floating
Connected
Reverse
OUT3 ? OUT2 ? OUT1
FIGURE 4-1:
Hysteresis.
Thermal Protection
to V BIAS
? 2011 Microchip Technology Inc.
DS22281A-page 9
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1026EBZEVB | BOARD EVAL FOR ADM1026 |
| ADN8831-EVALZ | BOARD EVAL FOR ADN8831 |
| ADP1043AFB100EVALZ | BOARD EVALUATION ADP1043A 100W |
| ADP1046-100-EVALZ | BOARD EVAL FOR ADP1046-100 |
| ADP1048-600-EVALZ | BOARD EVAL ADP1048-600 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM00352 | 功能描述:电源管理IC开发工具 MCP16301 600mA Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00360 | 功能描述:电源管理IC开发工具 MCP16301 300mA D2PAK Footprint Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADM00375 | 功能描述:BOARD EVAL FOR MCP6H04 OP AMP RoHS:否 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ADM00393 | 功能描述:电源管理IC开发工具 64KB Flash, 8KB RAM 16MIPS USBOTG Crypto RoHS:否 制造商:Exar 产品:Evaluation Boards 类型:DC/DC Converters, Regulators & Controllers 工具用于评估:XRP6670 输入电压:2.6 V to 5.5 V 输出电压:0.8 V to 5 V |
| ADM00397 | 制造商:Microchip Technology Inc 功能描述:MCP19111 EVALUATION BOARD - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:BOARD EVAL FOR MCP19111 |
发布紧急采购，3分钟左右您将得到回复。