参数资料
| 型号： | AD8036ANZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/24页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF ULDIST LN 70MA 8DIP |
| 标准包装： | 50 |
| 系列： | CLAMPIN™ |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 1200 V/µs |
| -3db带宽： | 240MHz |
| 电流 - 输入偏压： | 4µA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 20.5mA |
| 电流 - 输出 / 通道： | 70mA |
| 电压 - 电源，单路/双路(±)： | ±3 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 769 (CN2011-ZH PDF) |
| 配用： | AD8036-EB-ND - BOARD EVAL FOR AD8036 |
AD8036/AD8037
REV. B
–21–
Layout Considerations
The specified high speed performance of the AD8036 and
AD8037 requires careful attention to board layout and component
selection. Proper RF design techniques and low pass parasitic
component selection are mandatory.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance path. The ground plane should be removed from the
area near the input pins to reduce stray capacitance.
Chip capacitors should be used for supply and input clamp
bypassing (see Figure 17). One end should be connected to
the ground plane and the other within 1/8 inch of each power
and clamp pin. An additional large (0.47
F–10 F) tantalum
electrolytic capacitor should be connected in parallel, though
not necessarily so close, to supply current for fast, large signal
changes at the output.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the invert-
ing input will significantly affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). These should be designed with a
characteristic impedance of 50
or 75 and be properly termi-
nated at each end.
Evaluation Board
An evaluation board for both the AD8036 and AD8037 is
available that has been carefully laid out and tested to demon-
strate that the specified high speed performance of the device
can be realized. For ordering information, please refer to the
Ordering Guide.
The layout of the evaluation board can be used as shown or
serve as a guide for a board layout.
IN
RO
1k
VOUT
0.1 F
AD8036/
AD8037
VH
0.1 F
VL
RS
–VS
+VS
–VS
+VS
RG
RF
1k
–VS
+VS
RT
NONINVERTING CONFIGURATION
C5
10 F
+VS
–VS
C3
0.1 F
C1
0.01 F
C6
10 F
C4
0.1 F
C2
0.01 F
OPTIONAL
SUPPLY BYPASSING
Figure 17. Noninverting Configurations for Evaluation
Boards
Table I.
AD8036A
AD8037A
Gain
Component
+1
+2
+10
+100
+2
+10
+100
RF
140
274
2 k
2 k
274
2 k
2 k
RG
274
221
20.5
274
221
20.5
RO (Nominal)
49.9
49.9
49.9
49.9
49.9
49.9
49.9
RS
130
100
100
100
100
100
100
RT (Nominal)
49.9
49.9
49.9
49.9
49.9
49.9
49.9
Small Signal BW (MHz)
240
90
10
1.3
275
21
3
相关PDF资料 |
PDF描述 |
|---|---|
| 4-103783-0-35 | CONN HEADR BRKWAY .100 70POS STR |
| AD8224ACPZ-WP | IC AMP INST JFET R-R LP 16LFCSP |
| 929647-04-27-I | CONN HEADER .100 SNGL STR 27POS |
| AD8037ANZ | IC OPAMP VF ULDIST LN 70MA 8DIP |
| TMM-132-01-G-S-SM | CONN HEADER 32POS SNGL 2MM SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8036AR | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| AD8036AR-REEL | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk |
| AD8036AR-REEL7 | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD8036ARZ | 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8036ARZ | 制造商:Analog Devices 功能描述:IC OP-AMP 240MHZ 1200V/ SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。