参数资料
| 型号： | AD585SQ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/6页 |
| 文件大小： | 0K |
| 描述： | IC AMP SAMPLE HOLD 50MA 14CDIP |
| 标准包装： | 1 |
| 放大器类型： | 采样和保持 |
| 电路数： | 1 |
| 转换速率： | 10 V/µs |
| -3db带宽： | 2MHz |
| 电流 - 输入偏压： | 2nA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 10mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | ±5 V ~ 18 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-CERDIP |
| 包装： | 管件 |
AD585
REV. A
–6–
PRINTED
IN
U.S.A.
C851c–5–4/89
LOGIC INPUT
The sample-and-hold logic control was designed for versatile
logic interfacing. The HOLD and HOLD inputs may be used
with both low and high level CMOS, TTL and ECL logic sys-
tems. Logic threshold programmability was achieved by using a
differential amplifier as the input stage for the digital inputs. A
predictable logic threshold may be programmed by referencing
either HOLD or HOLD to the appropriate threshold voltage.
For example, if the internal 1.4 V reference is applied to HOLD
an input signal to HOLD between +1.8 V and +VS will place
the AD585 in the hold mode. The AD585 will go into the
sample mode for this case when the input is between –VS and
+1.0 V. The range of references which may be applied is from
(–VS +4 V) to (+VS –3 V).
OPTIONAL CAPACITOR SELECTION
If an additional capacitor is going to be used in conjunction
with the internal 100 pF capacitor it must have a low dielectric
absorption. Dielectric absorption is just that; it is the charge
absorbed into the dielectric that is not immediately added to or
removed from the capacitor when rapidly charged or discharged.
The capacitor with dielectric absorption is modeled in Figure 14.
Figure 14. Capacitor Model with Dielectric Absorption
If the capacitor is charged slowly, CDA will eventually charge to
the same value as C. But unfortunately, good dielectrics have
very high resistances, so while CDA may be small, RX is large and
the time constant RX CDA typically runs into the millisecond
range. In fast charge, fast-discharge situations the effect of di-
electric absorption resembles “memory”. In a data acquisition
system where many channels with widely varying data are being
sampled the effect is to have an ever changing offset which ap-
pears as a very nonlinear sample-to-hold offset since the differ-
ence between the voltage being measured and the voltage previ-
ously measured determines the fraction by which the
dielectric absorption figure is multiplied. It is impossible to
readily correct for this error source. The only solution is to use a
capacitor with dielectric absorption less than the maximum
tolerable error. Capacitor types such as polystyrene, polypropy-
lene or Teflon are recommended.
GROUNDING
Many data-acquisition components have two or more ground
pins which are not connected together within the device. These
“grounds” are usually referred to as the Logic Power Return
Analog Common (Analog Power Return), and Analog Signal
Ground. These grounds must be tied together at one point,
usually at the system power-supply ground. Ideally, a single
solid ground would be desirable. However, since current flows
through the ground wires and etch stripes of the circuit cards,
and since these paths have resistance and inductance, hundreds
of millivolts can be generated between the system ground point
and the ground pin of the AD585. Separate ground returns
should be provided to minimize the current flow in the path
from sensitive points to the system ground point. In this way
supply currents and logic-gate return currents are not summed
into the same return path as analog signals where they would
cause measurement errors.
Figure 15. Basic Grounding Practice
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
14-Pin Cerdip (Q-14)
20-Terminal LCC (E-20A)
20-Terminal PLCC (P-20A)
相关PDF资料 |
PDF描述 |
|---|---|
| AD602AR | IC AMP VGA DUAL LN 50MA 16SOIC |
| AD603AR | IC AMP VGA 90MHZ LN 50MA 8SOIC |
| AD604AR | IC AMP VGA DUAL ULN 40MA 24SOIC |
| AD605BRZ-RL | IC AMP VGA DUAL LN 40MA 16SOIC |
| AD606JR | IC AMP LOG LP 1.2MA 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD585SQ/883B | 功能描述:采样&保持放大器 IC - HI SPD SAMPLE/HOLD RoHS:否 制造商:Texas Instruments 通道数量:2 捕获时间:20 us 电源电压-最大:18 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 安装风格: 封装 / 箱体:SOIC-14 封装:Tube |
| AD586 | 制造商:AD 制造商全称:Analog Devices 功能描述:Ultralow Noise, High Accuracy |
| AD586_05 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Precision 5 V Reference |
| AD586A | 制造商:AD 制造商全称:Analog Devices 功能描述:High Precision 5 V Reference |
| AD586AR | 功能描述:IC VREF SERIES PREC 5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 标准包装:2,000 系列:- 基准类型:旁路，可调节，精度 输出电压:1.24 V ~ 16 V 容差:±0.5% 温度系数:- 输入电压:1.24 V ~ 16 V 通道数:1 电流 - 阴极:100µA 电流 - 静态:- 电流 - 输出:20mA 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:TO-226-3、TO-92-3（TO-226AA）成形引线 供应商设备封装:TO-92-3 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。