- 您现在的位置：买卖IC网 > PDF目录24863 > 950405AFLF (INTEGRATED DEVICE TECHNOLOGY INC) 300 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF资料下载
参数资料
| 型号： | 950405AFLF |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 300 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封装： | 0.300 INCH, GREEN, MO-118, SSOP-48 |
| 文件页数： | 6/18页 |
| 文件大小： | 219K |
| 代理商： | 950405AFLF |
14
ICS950405
0802F—04/22/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS950405
serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage)
that is present on these pins at this time is read and
stored into a 5-bit internal data latch. At the end of Power-
On reset, (see AC characteristics for timing values), the
device changes the mode of operations for these pins to
an output function. In this mode the pins produce the
specified buffered clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD
(logic 1) power supply or the GND (logic 0) voltage
potential. A 10 Kilohm (10K) resistor is used to provide
both the solid CMOS programming voltage needed during
the power-up programming period and to provide an
insignificant load on the output clock during the subsequent
operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the
series termination resistor to minimize the current loop
area. It is more important to locate the series termination
resistor close to the driver than the programming resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| 950515 | 20 A, MODULAR TERMINAL BLOCK, 1 ROW, 1 DECK |
| 950513 | 20 A, MODULAR TERMINAL BLOCK, 1 ROW, 1 DECK |
| 950511 | 20 A, MODULAR TERMINAL BLOCK, 1 ROW, 1 DECK |
| 950510 | 20 A, MODULAR TERMINAL BLOCK, 1 ROW, 1 DECK |
| 950509 | 20 A, MODULAR TERMINAL BLOCK, 1 ROW, 1 DECK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 950405AFLFT | 功能描述:时钟发生器及支持产品 RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| 9504-060-U500 | 制造商:Belden Inc 功能描述: |
| 950406-5002-AR | 功能描述:集管和线壳 6P BDMNT SKT 2R STRT PTH 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 950406-6102-AR | 功能描述:集管和线壳 6P BD MNT SKT 2R STRT PTH 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 950406-7203-AR | 功能描述:集管和线壳 6P BDMNT SKT 2R STRT PTH 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
发布紧急采购，3分钟左右您将得到回复。