- 您现在的位置：买卖IC网 > Datasheet目录613 > 91964-2 (TE Connectivity)S.D.E.PREM.DIE ASSY 22-16 PIDG Datasheet资料下载
参数资料
| 型号： | 91964-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/8页 |
| 文件大小： | 0K |
| 描述： | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 标准包装： | 1 |
| 系列： | * |
408-8732
SDE 1600
Power Unit
(ref)
Die Retaining
Screws
Indenter
Die
PIDG
Loctor
Assembly
Anvil
Dies
1. Loosen insulation adjustment locking screw
(see top of tool) and turn indicator to Position 4.
2. Place terminal or splice in tool dies.
3. Insert UNSTRIPPED wire into ONLY the
insulation barrel of terminal or splice.
4. Perform a crimp. Remove crimped terminal or
splice and check insulation grip as follows: Bend
the wire back and forth once. Terminal or splice
should retain grip on wire insulation.
5. If wire pulls out, set insulation adjustment
indicator to next tighter position - Position 3.
6. Perform a crimp and repeat adjustment as
necessary until desired insulation grip is
obtained. Do not use a tighter setting than
required.
6. MAINTENANCE AND INSPECTION
Barrel
Figure 3
7. Remove the crimped terminal or splice.
8. When crimping a butt splice, reposition the
uncrimped half in the stationary die. If the splice
cannot be turned around, turn the tool around,
load stripped wire in splice and cycle the power
unit.
9. Remove the butt splice.
Wire
Locator
Although the dies are inspected at the factory prior to
their shipment, it is recommended that a maintenance
and inspection program be performed at your facility
periodically. This is necessary to assure that continued
use of the dies will result in the same dependability
and uniform terminations for which the dies were
designed.
We recommend an initial frequency of once a month,
however frequency may be adjusted to suit your
requirements through experience. Frequency should
be dependant on:
? Care, amount of handling, and use of the dies;
? Type and size of the product being crimped;
? Degree of operator skill;
? Presence of abnormal amounts of dirt and dust;
and
? Your own established standards.
6.1. Maintenance
Tongue
Wire Barrel
Against Locator
1. Remove dust, moisture, and other
contaminants with a clean, soft brush, or a clean,
soft, lint-free cloth. Do NOT use any objects that
could damage the dies or tool.
2. Make sure that the proper die-retaining screws
are properly secured.
NOTE
Figure 4
5. NSULATION CRIMP ADJUSTMENT
PIDG terminals and splices feature an "insulation
grip."
i
Each tool has four insulation crimp positions. See
Figure 1.
Rev A
3. When the dies are not in use, store them in a
clean, dry area.
4. Store the tool with the tool handles closed to
prevent objects from becoming lodged within the
jaws
6.2. Visual Inspection
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
3 of 8
相关PDF资料 |
PDF描述 |
|---|---|
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
| 937317-1 | TOOL PUNCH MINI CT PISTOL GRIP |
| 947679-1 | TOOL HAND CRIMPER HE-14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91-9642-27 | 制造商:GLOBAL MEASUREMENT AND CONTROL 功能描述:WIRE PTFE A YELLOW 7/0.2MM 25M |
| 91964-P2S2 | 制造商:Nuvotem 功能描述:Transformer Toroidal 300VA 2x25V o/p |
| 91965-2 | 功能描述:冲压机与冲模 S.D.E.PREM.DIE ASSY 12-10 PIDG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 919655 | 制造商:Weidmuller 功能描述:CONN D-SUB F 50 POS SLDR ST PNL MNT 50TERM - Bulk |
| 919655-000 | 制造商:TE Connectivity 功能描述:CBL 1CNDCTR 26AWG 0.81MM SILV PLTD CPPR LGT GRN 600VAC - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:High Performance Cable 1Conductors 26AWG 0.81mm Silver Plated Copper Light Green 600VAC |
发布紧急采购，3分钟左右您将得到回复。