- 您现在的位置：买卖IC网 > PDF目录19195 > 90871-1 (TE Connectivity)PROCRIMPER III W/DIE 14-20AWG PDF资料下载
参数资料
| 型号： | 90871-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | PROCRIMPER III W/DIE 14-20AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，商用 0.093" |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，14-20 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 241 (CN2011-ZH PDF) |
| 配用： | 770144-6-ND - CONN SOCKET 20-14AWG CRIMP TIN A25779-ND - CONN SOCKET 14-20AWG GOLD CRIMP A25778-ND - CONN PIN 14-20AWG GOLD CIRMP A14097-ND - CONN SOCKET 14-20AWG TIN CRIMP A14099-ND - CONN PIN 14-20AWG TIN CRIMP |
| 其它名称： | A9818 |
408-9966
Nut
Locator
Chamfer
Wire
Crimper
Offset
Wire Anvil
Insulation
Crimper
Locator
Assembly
Tool Frame
Die Retaining
Pins
Insulation
Anvil
Chamfer
Die Retaining
Screw
Die Retaining
Screw
Figure 2
Die retaining pins and die retaining screws are used to
position and secure the dies in the tool frame. A nut is
used on the upper die retaining screw to hold the
locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE SET AND
LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
8. Carefully close the tool handles, making sure that
the anvils and crimpers align properly. Continue
closing the tool handles until the ratchet in the tool
frame has engaged sufficiently to hold the anvils
and crimpers in place, then tighten both die
retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the locator to slide up
and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the four
die retaining pins, and slide the anvils and crimpers
out of the tool jaws.
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
NOTE
i
The contact support is preset prior to shipment, but
minor adjustment may be necessary. ?
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
Rev C
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator assembly.
2 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90869-1 | TOOL CRIMP .062 AWG 24 W/DIE |
| 210-5MSD | SWITCH RAISED ACTUATOR 5 SEC |
| 210-5LPSD | SWITCH SPST 5 SEC STRAIGHT TERM |
| 210-5ESF | SWITCH EXTENDED ACTUATOR 5 SEC |
| 90575-1 | ASSY PRO-CRMPR COMM M-N-L20-14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90871-1001 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 5CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-1501 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 6CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-2 | 功能描述:冲压机与冲模 DIE SET 20-14 .093 PRO CRIMP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 90871-2001 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 7CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 90871-2501 | 功能描述:板对板与夹层连接器 90871 DIR/INDIR FEM. /INDIR FEM. 2.5 8CKT RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
发布紧急采购，3分钟左右您将得到回复。