- 您现在的位置：买卖IC网 > PDF目录19195 > 90575-1 (TE Connectivity)ASSY PRO-CRMPR COMM M-N-L20-14 PDF资料下载
参数资料
| 型号： | 90575-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | ASSY PRO-CRMPR COMM M-N-L20-14 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，商用 MATE-N-LOK |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，14-20 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 229 (CN2011-ZH PDF) |
| 配用： | A106252-ND - CONN SOCKET M-N-L 14-20AWG TIN 170121-1-ND - CONN SOCKET M-N-L 14-20AWG TIN A25561-ND - CONN PIN 14-20AWG TIN CRIMP A25562-ND - CONN SOCKET 14-20AWG TIN CRIMP A25565-ND - CONN SOCKET 14-20AWG GOLD CRIMP A25568-ND - CONN PIN 16-18AWG TIN CRIMP A25570-ND - CONN SOCKET 16-18AWG TIN CRIMP A1435-ND - CONN SOCKET 14-20AWG GOLD CRIMP A1434-ND - CONN PIN 14-20AWG GOLD CRIMP A1421-ND - CONN SOCKET 14-20AWG TIN CRIMP 更多... |
| 其它名称： | 90575-1-ND A25419 |
PRO- CRIMPER III Hand Crimping Tool Assembly 90575- 1
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
408- 9887
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
NOTE
i
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
1. Remove the lockscrew from the ratchet
adjustment wheel.
Screwdriver
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET (Crimp Height)
ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Proceed as follows:
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
Position Point
on Center of
Wire Barrel
Opposite
Seam
Figure 5
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
4. Replace the lockscrew.
Modified Anvil
Wire Size
AWG (Max)
14
Crimp Section
(Wire Size Marking)
20--14
“A”
Crimp Height
Dimension A
(+0.05 [+.002])
1.35 + .05
[.053 + .002]
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
8. MAINTENANCE
15--14
(1) 18 1.63 + .05
and (1) 16 [.064 + .002]
Figure 4
3. Using a crimp--height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
4 of 6
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| FDD16AN08A0 | MOSFET N-CH 75V 50A D-PAK |
| NTMS5P02R2G | MOSFET P-CH 20V 3.95A 8-SOIC |
| NTLUS3A40PZTAG | T4 20/8 PCH 2X2 UDFN SING |
| 357LB3I038M8800 | OSC VCXO 38.8800 MHZ 5X7MM SMD |
| 357LB3I006M1760 | OSC VCXO 6.1760 MHZ 5X7MM SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90575-2 | 功能描述:冲压机与冲模 PRO-CRIMPER DIE ASSY COMM M-N-L RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 905-755 | 功能描述:支架与垫片 Plastic Spcr .755 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 905759-0002 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 905759-2 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 905-760 | 功能描述:支架与垫片 Plastic Spcr .76 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。