- 您现在的位置：买卖IC网 > Datasheet目录611 > 90390-3 (TE Connectivity)DIE SET ULTRA-FASTONS 22-18 AWG Datasheet资料下载
参数资料
| 型号： | 90390-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET ULTRA-FASTONS 22-18 AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Faston |
| 压接或电缆尺寸： | 18-22 AWG |
| 压接手柄： | A28005-ND |
| 连接器类型： | 端子及连接件 |
| 产品目录页面： | 375 (CN2011-ZH PDF) |
| 配用： | 8-520335-1-ND - CONN RECEPT FAST 18-22AWG .187 8-520194-1-ND - CONN RECEPT FAST 18-22AWG .187 8-520084-1-ND - CONN RECEPT FAST 18-22AWG .110 8-520182-1-ND - CONN FAST RECEPT 18-22 AWG .187 8-520103-1-ND - CONN TAB ULTRA FAST 18-22 AWG 8-520184-1-ND - CONN FAST RECEPT 18-22 AWG .250 8-520129-1-ND - CONN FAST FLG RCPT 18-22AWG .250 8-520273-1-ND - 110 ULTRA-FAST RCPT 22-18 TPBR 8-520264-1-ND - CONN RECEPT FAST 18-22 AWG .250 8-520337-1-ND - CONN RCPT FLG FAST 18-22AWG .187 更多... |
| 相关产品： | A28005-ND - HAND CRIMP TOOL/FASTOS(W/O DIES) |
| 其它名称： | 90390-3-ND A28007 |
408-9279
5.2. Periodic Inspection
Suggested Plug Gage Design
Regular inspection should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to the
supervisory personnel responsible for the tool. Though
recommendations call for at least one inspection a
month, the inspection frequency should be based on
the amount of use, ambient working conditions,
operator training and skill, and established company
standards. These visual inspections should be
performed in the following sequence:
1. Remove all lubrication and accumulated film by
immersing the dies in a suitable degreaser that
will not affect paint or plastic material.
2. Make sure all die holding screws and die
components are in place. Refer toe parts listed in
Figure 6 if replacements are necessary.
GO Dia
NO-GO Element Must Not Pass
Through Crimping Chamber
NO-GO Dia
3. Check all bearing surfaces. Remove and
replace worn components.
4. Inspect the crimp area for flattened, chipped,
GO Element Must Pass
Through Crimping Chamber
cracked, worn or broken areas. If damage is
evident, the dies must be repaired before
returning them to service. Refer to Section 6,
PLATFORM
DIE
NUMBER
TERMINAL
NO. (LP)
ELEMENT DIAMETER
GO NO-GO
REPAIR.
5.3. Gaging the Crimping Chamber
This inspection requires the use of a plug gage
conforming to the diameters in Figure 5.
TE Connectivity does not manufacture or market these
gages.
Proceed as follows:
1. Mate the dies until it is evident that they have
bottomed. Hold the dies in this position with a
pressure of approximately 69 kPa [10 psi].
2. 2.Align the GO element with the wire barrel
crimping chamber. Push element straight into the
crimping chamber without using force. The GO
element must pass completely through the
crimping chamber as shown in Figure 5.
3. Align the NO-GO element and try to insert it
straight into the same crimping chamber. The
NO-GO element may start entry but must not
90390-3
90391-3
520081
520084
520273
520182
520194
520275
520184
520264
520103
520129
520335
520337
350616
520125
520151
350820
520117
520107
520141
520133
520339
1.575-1.582
[.0620-.0623]
1.829-1.836
[.0720-.0723]
1.725-1.727
[.0679-.0680]
1.979-1.981
[.0779-.0780]
pass completely through, as shown in Figure 5.
If the crimping chamber conforms to the gage
inspection, the dies are considered dimensionally
correct and should be lubricated with a THIN coat of
SAE 20 motor oil. If not, the dies must be repaired
before returning them to service.
For additional information concerning the use of a plug
gage, refer to Instruction Sheet 408-7424.
Rev E
Figure 5
6. REPLACEMENT AND REPAIR
The parts listed in Figure 6 are customer- replaceable.
A complete inventory can be stocked and controlled to
prevent lost time when replacement of parts is
necessary. Order replacement parts through your TE
Representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 1-717-986-7605, or
write to:
4 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 90431-1 | TOOL CERTI-CRIMP HAND 20-24AWG |
| 904379-1 | CONNECTOR KIT ULTRA ATA |
| 90471-1 | EXTRACTION TOOL |
| 904800-1 | SEATING TL. ASSY 2MMHM V.COAX |
| 90575-2 | TOOL DIESET 14-20AWG COM-MATE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90390-3 CAL | 制造商:TE Connectivity 功能描述:CALIBRATED - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 H 制造商:TE Connectivity / AMP 功能描述:CALIBRATED - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 Hand Crimp Too |
| 90390-3 CAL D | 制造商:TE Connectivity 功能描述:CALIBRATED W/DATA - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58 制造商:TE Connectivity / AMP 功能描述:CALIBRATED W/DATA - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 Hand Crimp Too |
| 90390-3 CAL DU | 制造商:TE Connectivity 功能描述:CALIBRATED W/ DATA & UNCERTAINTIES - Tools, Dies, Crimp Size:22AWG to 16AWG, For 制造商:TE Connectivity / AMP 功能描述:CALIBRATED W/ DATA & UNCERTAINTIES - Tools, Dies, Crimp Size:22AWG to 16AWG, For Use With:Tyco 58078-3 Hand Crimp Too |
| 90390-3 | 制造商:TE Connectivity 功能描述:Crimping Tool Die Set for Faston Recep |
| 90391-3 | 功能描述:冲压机与冲模 DIE SET 16-14 AWG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。