参数资料
| 型号： | 901-260 |
| 厂商： | Littelfuse Inc |
| 文件页数： | 2/41页 |
| 文件大小： | 0K |
| 描述： | O RING KNOB |
| 标准包装： | 1 |
| 附件类型： | 旋钮 |
| 适用于相关产品： | 保险丝座; 571 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
Blocks and Holders
Fuse Blocks
General Information
4. Determine if NEC, CSA, UL, or other requirements
are applicable
If fuse blocks will be installed in equipment to be submitted for agency
approval, the requirements should be obtained from the approving
agency in advance of fuse and fuse block selection.
5. Select the type of wire termination
A choice of three types of wire termination is available:
a) Screw* — for use with spade lugs or ring terminals.
b) Screw with Pressure Plate* — for use with solid or stranded wire
without terminal. Recommended where vibration will be a factor.
c) Box Lug — the most durable. For use with all types of solid wire and
Class B and Class C stranded wire. Not for use with welding cable or
other rope-stranded conductors.
* 1 / 4 ” Quick Connect terminals rated for up to 20A are
available on the Midget and Class CC fuse blocks.
Fuse Block Selection
The following guidelines should help simplify the selection of proper
fuse blocks:
1. Determine the system voltage
Since fuses are selected on the basis of system voltage, fuse blocks are
selected to match the voltage rating of the fuse.
Screw
with
Pressure
Plate
(P)
Screw
(S)
Box
Lug
(C)
6. Decide on the number of poles in each block
2. Determine the design short-circuit current
Available and/or design short-circuit current is an important
consideration when determining the class of fuse and fuse blocks to
use. If available short-circuit current cannot be determined, or if it will
vary with equipment location, select fuses with a 200,000 ampere
interrupting rating (A.I.R.) and mating fuse blocks with a withstand rating
of 200,000 amperes for maximum safety.
Class H fuse blocks will accept Class H or K5 fuses (which have an
interrupting rating of up to 50,000 amperes) and Class R fuses (which
have a 200,000 A.I.R.). To prevent the possibility of inserting a fuse
with the incorrect interrupting rating, the use of Class R fuse blocks is
recommended for use with Class R fuses. Use Class H fuse blocks with
Class H or K5 fuses. These fuse blocks are dimensionally the same, but
the Class R fuse blocks incorporate a rejection feature which allows only
Class R fuses to be inserted.
3. Determine the type and ampere rating of the fuse to be used
In addition to voltage and interrupting rating as discussed above, the
fuse ampere rating, opening characteristics (fast acting or time-delay)
and size are other important considerations in fuse selection. Once the
fuse type is selected, the mating fuse block can be chosen. Fuse blocks
are available in 30, 60, 100, 200, 400 and 600 amp ratings, and may be
used with a fuse rated at the corresponding amperage rating or below.
For example, a fuse block rated at 30 amperes may be used with a fuse
rated from 0 to 30 amperes.
The number of poles for each set of fuses is determined by the
characteristics of the circuit. The option to gang individual fuse blocks
into long strips will be determined by the available space and by the
type of wire being used.
7. Determine if fuse clips need to be reinforced
Fuse clips may have a tendency to lose some of their tension over a
period of time. This may be prevented by specifying reinforced fuse
clips. Reinforced clips are standard on certain fuse blocks (see individual
product pages).
Ordering Information
The Littelfuse fuse block part number consists of 6 or 7 components, as
shown below and in the individual fuse block data tables.
For all Class R, H, J, T and 15, 20
& 60A Class G Fuse Blocks
For all Class CC, Midget and 30A
Class G Fuse Blocks
? 2005 Littelfuse ? POWR-GARD ? Products Catalog
www.littelfuse.com
111
相关PDF资料 |
PDF描述 |
|---|---|
| RCWL1218R130JNEA | RES .13 OHM 1W 5% 1218 SMD |
| RCWL1218R120JNEA | RES .12 OHM 1W 5% 1218 SMD |
| 8-31890-1 | CONN RING 16-22 AWG #8 RED PIDG |
| LT600303SR | FUSEBLOCK CLASS T 30A 3 POLE |
| MAX410CPA+ | IC OPAMP PREC SINGLE 28MHZ 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9012-60 | 制造商:American Beauty Tools 功能描述:60 WATT HEATING ELEMENT (3112) |
| 9012600000 | 制造商:Weidmuller 功能描述:CONN ACC CRMPING TOOL - Bulk 制造商:Weidmuller 功能描述:PZ 16 CRIMPTOOL 10-6 AWG 制造商:Weidmuller 功能描述:CRIMP TOOL STRIPAX PZ 16 制造商:Weidmuller 功能描述:CRIMP TOOL, STRIPAX, PZ 16 制造商:Weidmuller 功能描述:CRIMP TOOL, WIRE-END FERRULE; Crimp Application:End Sleeves (Ferrules); Crimp Size:6mm to 16mm ;RoHS Compliant: Yes 制造商:Weidmuller 功能描述:Crimping Tool For Wire End Ferrules, Crimping Range 6 16mm Square , Indent Crimping 制造商:Weidmuller 功能描述:PZ16 3 profile crimping head,6-16sq.mm |
| 901260RE | 制造商:Weidmuller 功能描述: |
| 9012640000 | 功能描述:DIE SET FOR 10-16AWG WIRE RoHS:否 类别:工具 >> 模具組 系列:* 标准包装:1 系列:* 其它名称:CRIMPFOX-RCI 6-1/DIECRIMPFOX-RCI6-1/DIE |
| 901-265 | 功能描述:支架与垫片 Plastic Spcr .265 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。