- 您现在的位置：买卖IC网 > Datasheet目录610 > 9-1478240-0 (TE Connectivity)TOOL HAND CRIMPING SDE PEW 12 Datasheet资料下载
参数资料
| 型号： | 9-1478240-0 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/3页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMPING SDE PEW 12 |
| 标准包装： | 1 |
| 系列： | SDE PEW 12 |
| 工具类型： | 手持压接器 - 无模具 |
| 适用于相关产品： | 因模具套件而异 |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 461 (CN2011-ZH PDF) |
| 配用： | 2063778-2-ND - CONN HAND TOOL DIE 22-18AWG A97886-ND - DIE HEX RG58-RG59-URM70 58522-2-ND - TOOL DIE ASSEM FOR 58522-1 A30040-ND - DIE SET FOR PRO-C III 22-20,18 A30039-ND - DIE SET FOR PRO-C III 26-22 AWG 58529-2-ND - TOOL DIE SET CRIMP TERMINAL A100343-ND - DIE USE WITH 354940-1 FOR SL156 A19531-ND - DIE SET CST-100 A9816-ND - DIE SET HI-DEN D-SUB CRIMP CONT A9814-ND - DIE SET D-SUB CRIMP CONTACTS 更多... |
| 其它名称： | 9-1478240-0-ND A97885 |
408-8851
4. Inspect the tool frame for wear or damage,
paying particular attention to the tool jaws and pivot
points. If damage is evident, refer to Section 6,
TOOL REPLACEMENT. If tool is acceptable,
lubricate and return to service.
Ratchet Wheel Adjustment Screw
NOTE
i
This tool is recommended for R&D prototyping,
networking applications, commercial/industrial
maintenance, and field service repair. For other
applications, please contact your Tyco Electronics
Sales Representative or the Tyco Electronics
Tooling Assistance Center at 1-800-722-1111.
5. CRIMP HEIGHT INSPECTION
The crimp height is dependant on the dies. Refer to
the appropriate instruction sheet for die crimp height
inspection.
6. RATCHET (Crimp Height) ADJUSTMENT (Figure 4)
Adjustment Wheel
Retaining Plate
NOTE
i
the end of the wire and replaced with a new one.
Never reuse or re-terminate a terminal.
The tool frame assembly features a ratchet
mechanism and adjustment wheel with a range of
settings. The ratchet mechanism ensures that the tool
has completed the cycle. The adjustment wheel
controls the amount of handle pressure exerted on the
tool jaws and crimping dies during the crimping
procedure. Although the ratchet is preset prior to
shipment, it is important that you verify the crimp
height. Also, general use and subsequent wear may
cause the tool to go out of adjustment. It is
recommended that the crimp height be inspected -
and adjusted, if necessary - on a regular basis by
quality control personnel.
This is a general explanation of the procedure. For
specific information, refer to the instruction sheet
packaged with the die assembly.
1. Crimp a contact onto a properly-prepared wire of
the correct size.
CAUTION Damaged product should not be used. If a
damaged contact is evident, it should be cut from
!
2. If the crimp height is greater than recommended,
remove the ratchet wheel adjustment screw and
rotate the adjustment wheel counterclockwise (+) to
a higher setting. Repeat as required.
3. If the crimp height is less than recommended,
remove the ratchet wheel adjustment screw and
rotate the adjustment wheel clockwise (-) to a lower
setting. Repeat as required.
4. If the crimp cannot be made to conform to the
dimensions provided in the appropriate product
application specification, the tool and/or dies are
defective and must be replaced.
Rev C
Figure 4
7. TOOL REPLACEMENT
SDE-SA Hand Crimping Tool Frame Assembly
9-1478240-0 is inspected prior to shipment. It is
recommended that it be inspected upon arrival to
ensure that it has not become damaged during
shipping.
Additional tools may be ordered from:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
8. REVISION SUMMARY
Since the previous release of this document, the new
company logo has been applied.
3 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 90017-3 | ASSY SAHT |
| 90026 | TOOL SHORT HANDLE 24-22AWG CRIMP |
| 90045 | DAHT F CRIMP 14-18 |
| 90050-1 | DAHT TAPER PIN 16-20 |
| 90062 | DAHT F CRIMP 14-24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9-1478242-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE RG58-RG59-URM70 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478243-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE PSF 1/2-BEL8281 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478245-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE PSF1/7 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478246-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE RG9-RG214-URM90 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478247-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE BT2003 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。