- 您现在的位置：买卖IC网 > Datasheet目录601 > 58707-2 (TE Connectivity)TOOL DIE SET ONLY 16-20 AWG Datasheet资料下载
参数资料
| 型号： | 58707-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET ONLY 16-20 AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，微型通用 MATE-N-LOK |
| 压接或电缆尺寸： | 16-20 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 配用： | A34924-ND - CONN PIN 16-20AWG GOLD CRIMP A32447-ND - CONN SOCKET 16-20AWG GOLD CRIMP A28815-ND - CONN SOCKET 16-20AWG GOLD CRIMP A28814-ND - CONN SOCKET 16-20AWG TIN CRIMP A28807-ND - CONN PIN 16-20AWG GOLD CRIMP A28806-ND - CONN PIN 16-20AWG TIN CRIMP A25691-ND - CONN PIN 16-20AWG TIN CRIMP A25692-ND - CONN SOCKET 16-20AWG TIN CRIMP |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A30727 |
PRO- CRIMPER III Hand Crimping Tool Assembly 58707- 1
408- 4503
CAUTION
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Position Point
on Center of
Wire Barrel
Opposite
Seam
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
Modified Anvil
“A”
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
Wire Size
AWG (Maxi-
mum)
18
16
Crimp Section
(Wire Size Marking)
20--18
16, 2 (20)
Figure 4
Crimp Height
Dim. (A) and
Tolerance
+.051 [+.002]
1.07 [.042]
1.30 [.051]
NOTE
i
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET (Crimp Height)
ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
Screwdriver
Ratchet
Adjustment
Wheel
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
Lockscrew
(Typ)
Figure 5
4 of 5
Tyco Electronics Corporation
Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| 59239-8 | TOOL HAND 10-12AWG 14-16AWG HD |
| 59275 | TOOL CERTI-CRIMP PLASTI-G 20-26 |
| 59287-2 | TOOL HAND HEAVY PIDG 10-12AWG |
| 59461 | TOOL HAND W-DG STRATO 10-12AWG |
| 59524-1 | TOOL HAND STR ACTION 26-20AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5870R-0001A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0002A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0003A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0004A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0005A | 制造商:LG Corporation 功能描述:OPENER |
发布紧急采购，3分钟左右您将得到回复。