- 您现在的位置：买卖IC网 > Datasheet目录601 > 58644-1 (TE Connectivity)TOOL HEAD MTA .100 MASS INSERT Datasheet资料下载
参数资料
| 型号： | 58644-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD MTA .100 MASS INSERT |
| 标准包装： | 1 |
| 系列： | * |
408-4406
Wire Insertion Depth
Insertion ?
Rod ?
Adjuster
Head Removed from
Handle Assembly
Clockwise to
Decrease
Counterclockwise
to Increase
6.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. Though recommendations call for
at least one inspection a month, the frequency should
be based on amount of use, working conditions,
operator training and skill, and your established
company policies.
1. Remove all lubrication and accumulated film by
immersing the head in a suitable commercial
degreaser that will not affect paint or plastic.
2. Make certain all components are in place. If
replacements are necessary, refer to Section 7.
3. Check all bearing surfaces for wear. Replace
worn or damaged parts.
4. Inspect the head for flattened, chipped, or broken
Figure 6
2. If the wires are too deep in the contact slots, turn
the insertion rod adjuster clockwise. A 1/6-
revolution will decrease the wire insertion depth by
approximately 0.20 mm [.008 in.]. If the wires are
not deep enough in the contact slots, turn the
adjuster counterclockwise. A 1/6-revolution will
increase the wire insertion depth by approximately
3. Install the head onto the handle assembly; then
terminate and inspect a test connector.
4. Repeat the adjustment as necessary until proper
wire insertion depth is obtained. DO NOT use a
tighter setting than required.
6. MAINTENANCE AND INSPECTION
TE recommends that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations.
6.1. Daily Maintenance
1. Remove dust, moisture, and other contaminants
with a clean, soft brush or a soft, lint-free cloth. Do
NOT use objects that could damage the head.
2. Make sure that all pins, rings, and other
components are in place and secure.
3. When head is not in use, store it in a clean, dry
area.
Rev C
surfaces. Replace worn or damaged parts.
7. REPLACEMENT AND REPAIR
Replacement parts are listed in Figure 7. A complete
inventory can be stocked and controlled to prevent lost
time when replacement of parts is necessary. Order
replacement parts through your TE representative, or
call 1-800-526-5142, or send a facsimile of your
purchase order to 1-717-986-7605, or write to:
CUSTOMER SERVICE (038-035) ?
TYCO ELECTRONICS CORPORATION ?
PO BOX 3608 ?
HARRISBURG PA 17105-3608
For customer repair service, call 1-800-526-5136.
8. REVISION SUMMARY
Revisions to this instruction sheet include:
? Changed company name and logo
4 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
| 59239-8 | TOOL HAND 10-12AWG 14-16AWG HD |
| 59275 | TOOL CERTI-CRIMP PLASTI-G 20-26 |
| 59287-2 | TOOL HAND HEAVY PIDG 10-12AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58644-2 | 制造商:TE Connectivity 功能描述:MTA .100 MASS INSERTION PGH - Bulk |
| 5864-5001-09 | 功能描述:RF 连接器 PCB R/A Jack Rcept 50 OHM RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 5864-5001-10 | 功能描述:RF 连接器 MCX RA JCK PCB .155LG RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 5864-5002-10 | 功能描述:RF 连接器 OSX RA PCB JACK MICRO MIN SMT RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 5864-5003-10 | 功能描述:RF 连接器 MCX RA JCK PCB .115LG RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
发布紧急采购，3分钟左右您将得到回复。