- 您现在的位置：买卖IC网 > Datasheet目录601 > 58545-1 (TE Connectivity)DIE SET UNINSULATED TERMINALS Datasheet资料下载
参数资料
| 型号： | 58545-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET UNINSULATED TERMINALS |
| 特色产品： | SOLISTRAND?, Budget, and DIAMOND GRIP? Terminals and Splices |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Solistrand |
| 压接或电缆尺寸： | 10-22 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 端子及连接件 |
| 产品目录页面： | 384 (CN2011-ZH PDF) |
| 配用： | 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 1-34108-1-ND - CONN RING UNINS 16-22AWG #8 8-53555-1-ND - CONN SPADE 22-16AWG #2 SOLIS 8-35476-2-ND - CONN RING 12-10AWG #6 SOLIS 8-34126-1-ND - TERM RING 16-14AWG #3/8 SOLIS 8-34125-1-ND - TERM RING 16-14AWG #5/16 SOLIS 8-34114-1-ND - CONN RING 22-16AWG #5/16 SOLIS 8-34112-1-ND - CONN RING 16-22 AWG #10 SOLIS 8-34111-1-ND - CONN RING 22-16AWG #8 SOLIS 8-33459-2-ND - CONN RING 12-10AWG #5/16 SOLIS 更多... |
| 相关产品： | A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9813 |
The GO element must pass completely through the
crimping chamber. See Figure 5.
4. Align the NO–GO element and try to insert it
straight into the same crimping chamber. The
NO–GO element may start entry, but must not
pass completely through the crimping chamber.
See Figure 5.
Figure 6
The frame assembly ratchet mechanism features an
adjustment wheel with numbered settings. If the dies
do not bottom, adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the opposite side of the frame.
3. Observe the ratchet adjustment wheel. If the
dies do not bottom, rotate the adjustment wheel
COUNTERCLOCKWISE to a higher–numbered
setting.
4. Replace the lockscrew.
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
Figure 5
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
If the crimping chamber conforms to the gage
inspection, the tool is considered dimensionally
correct, and should be lubricated with a THIN coat of
any good SAE 20 motor oil. If not, the tool must be
returned to Tyco Electronics for further evaluation and
repair. Refer to Section 8, REPLACEMENT.
For additional information regarding the use of a plug
gage, refer to Instruction Sheet 408–7424.
The die assembly should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimping chambers for
flattened, chipped, worn, or broken areas. If damage
or abnormal wear is evident, the tool or dies must be
replaced. See Section 8, REPLACEMENT.
相关PDF资料 |
PDF描述 |
|---|---|
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58545-2 | 功能描述:冲压机与冲模 SOLISTRAND 10-22 DIE ASSY RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58545-3 | 功能描述:冲压机与冲模 SDE DIE ASSY. 22-10 SOLISTRAND RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58545-4 | 功能描述:冲压机与冲模 SOLISTRAND 10-22 DIE ASSY. RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58546-1 | 功能描述:折皱器 TOOL W/DIE UNINS TRM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58546-2 | 功能描述:折皱器 SOLIS 22-10AWG W/DIE AS (-1) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。