- 您现在的位置：买卖IC网 > Datasheet目录601 > 58541-2 (TE Connectivity)TOOL DIE FOR PRO-CRIMPER II Datasheet资料下载
参数资料
| 型号： | 58541-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE FOR PRO-CRIMPER II |
| 标准包装： | 1 |
| 系列： | * |
408-4051
Back of Tool
(Wire Side)
Contact (Typ)
Strip Length
Locator
Wire
Contact Shoulder
Against Locator
Wire Inserted
In Contact
Figure 3
i NOTE This tool is provided with a crimp adjustment feature.
i NOTE TE does not manufacture or market these gages.
4. CRIMPING PROCEDURE
NOTE
Initially, the crimp height should be verified as specified
in Figure 4. Refer to Section 5, Crimp Height Inspection,
and Section 6, Crimp height Adjustment, to verify crimp
height before using the tool to crimp desired contacts
and wire sizes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire to
the length indicated in Figure 1, taking care not to nick
or cut wire strands. Select an applicable contact and
identify the appropriate crimp section according to the
wire size markings on the tool. Refer to Figure 3 and
proceed as follows:
1. Hold the tool so that the back (wire side) is facing
you. Squeeze tool handles together and allow them
to open fully.
2. Holding the contact by the mating end, insert the
contact - insulation barrel first - through the front of
the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of the
contact is on the locator side of the tool. Refer to
Figure 3. Butt the contact shoulder against the
locator.
4. Hold the contact in position and squeeze the tool
handles together until ratchet engages sufficiently to
hold the contact in position. Do NOT deform
insulation barrel or wire barrel.
5. Fully insert the stripped wire into the contact as
shown in Figure 3.
6. While holding the wire in place, squeeze the tool
handles together until ratchet releases. Allow the
tool handles to open, and remove the crimped
contact.
7. Check the contact's crimp height as described in
Section 5, Crimp Height Inspection. If necessary,
adjust the crimp height as described in Section 6,
CRIMP HEIGHT ADJUSTMENT.
5. CRIMP HEIGHT INSPECTION
This inspection requires the use of a micrometer with a
modified anvil.
NOTE
However, TE recommends the modified micrometer
(Crimp Height Comparator RS-1019-5LP).
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
!
Rev D
CAUTION
Do not attempt to crimp an improperly positioned
contact.
size) for each crimp section listed.
2. Refer to Section 4, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 58545-1 | DIE SET UNINSULATED TERMINALS |
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5854121 | 制造商:Dialight 功能描述:LED Uni-Color Red 630nm 2-Pin |
| 585-4121 | 功能描述:LED替换灯-基于LED BAYONET RED 6V NON-P RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5854123 | 制造商:Dialight 功能描述:LED Uni-Color Red 630nm 2-Pin |
| 585-4123 | 功能描述:LED替换灯-基于LED RED 14V MULTI-CHIP RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5854125 | 制造商:Dialight 功能描述:LED Uni-Color Red 630nm 2-Pin |
发布紧急采购，3分钟左右您将得到回复。