- 您现在的位置：买卖IC网 > Datasheet目录601 > 58517-4 (TE Connectivity)TOOL PRO-CRIMPER II DIE SET Datasheet资料下载
参数资料
| 型号： | 58517-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL PRO-CRIMPER II DIE SET |
| 标准包装： | 1 |
| 系列： | * |
408-4064
Nut
Adjustment Screw
(See Figure 3)
Nut
Tool Frame
(or Bench
Machine, or
Ratched Hand
Tool)
Washer
Chamfer
Wire
Crimper
Offset
Locator
Wire Anvil
Insulation
Crimper
Insulation
Anvil
Chamfer
Figure 2
Die Retaining Screws
Die
Retaining
Pins
Die retaining pins and die retaining screws are used to
position and secure the dies in the tool frame. A
washer and nut is used on the lower die retaining
screw to hold the locator in place.
3. INSTALLATION AND REMOVAL OF DIE SET AND
LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil in the
moving jaw so that their chamfered sides and
their marked surfaces face outward, when
mounted in the moving jaw of the tool frame.
3. Insert the two die retaining pins.
4. Insert the long die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do
not tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator over the end of the long
screw, and position the locator against the side of
the tool jaw.
10. Place the washer and nut onto the end of the
long screw. Align the locator slot with the
crimping section and carefully tighten the nut.
11. To disassemble, close the tool handles until
the ratchet releases, remove the nut, the washer,
the locator, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
4. CRIMPING PROCEDURE
5. Place the wire crimper and insulation crimper
in the stationary jaw so that their chamfered sides
and their marked surfaces face outward, when
mounted in the stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the short die retaining screw through the
jaw and through both crimper dies, and tighten
the screw just enough to hold the dies in place.
Do not tighten the screw completely at this time.
Rev F
NOTE
i
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be verified
as specified in Figure 4. Refer to Section 6, Crimp
Height Inspection, and Section 7, Crimp Height
Adjustment, to verify crimp height before using the
tool to crimp desired contacts and wire sizes.
2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58519-1 | TOOL CRIMP F/OPTIC FSD STYLE |
| 58529-2 | TOOL DIE SET CRIMP TERMINAL |
| 58532-1 | TOOL FIBER OPTIC PRO CRIMPER III |
| 58541-2 | TOOL DIE FOR PRO-CRIMPER II |
| 58545-1 | DIE SET UNINSULATED TERMINALS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58517-5 | 制造商:TE Connectivity 功能描述:SDE DIE SET, BENCH/BATTERY - Bulk |
| 5851-7BR005 | 制造商:Alpha Wire Company 功能描述:Brown hook-up equipment wire,30awg |
| 5851-8 OR005 | 制造商:Alpha Electronics Corporation 功能描述:EQUIPMENT WIRE 30AWG ORG |
| 58518 | 制造商:Alpha Wire Company 功能描述:WIRE UL1213 30 AWG ORANGE 30.5M |
| 5851814001 | 制造商:TE Connectivity 功能描述:HEAT SHRNK TBING POLYFN YLLW SPL - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:HEAT SHRINK TUBING 制造商:TE Connectivity 功能描述:MT5000-3/32-4-SP 制造商:TE Connectivity 功能描述:Heat Shrink Tubing ST Polyolefin Yellow Thin Spool |
发布紧急采购，3分钟左右您将得到回复。