- 您现在的位置：买卖IC网 > PDF目录19195 > 58517-1 (TE Connectivity)TOOL CRIMP W/DIE CST-100 PDF资料下载
参数资料
| 型号： | 58517-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP W/DIE CST-100 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, CST-100 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，22-26 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 199 (CN2011-ZH PDF) |
| 配用： | A23962-ND - CONN SOCKET 22-26AWG GOLD CRIMP A19520-ND - CONN TERM CRIMP CST-100 TIN |
| 其它名称： | A19530 |
408-4064
.
Screwdriver
WIRE SIZE
AWG (Max)
22
CRIMP SECTION
(WIRE SIZE
MARKING)
26-22
CRIMP HEIGHT
DIM (A) AND
TOLERANCE (±)
0.79±0.05
[.031±.002]
Ratchet
Adjustment
Pawl
Lockscrew
Figure 4
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the
use of a micrometer with a modified anvil,
commonly referred to as a crimp height comparator.
Tyco Electronics does not market crimp height
comparators. Refer to Instruction Sheet 408-7224
for detailed information on obtaining and using a
crimp height comparator.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for the crimp section.
2. Refer to Section 4, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If
the crimp height conforms to that shown in the
table, the tool is considered dimensionally
correct. If not, the tool must be adjusted. Refer to
Section 7, CRIMP HEIGHT ADJUSTME
7. .CRIMP HEIGHT ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a higher-
numbered setting. If a looser crimp is required,
rotate the adjustment wheel CLOCKWISE to a
lower-numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace
and secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Rev F
Figure 5
8. MAINTENANCE
Ensure that the tool and dies are clean by wiping them
with a clean, soft cloth. Remove any debris with a
clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in the
crimping dies, and store in a clean, dry area.
9. VISUAL INSPECTION
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp section for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
See Section 10, REPLACEMENT.
10. REPLACEMENT
Customer-replaceable parts are shown in Figure 1.
Available separately, PRO-CRIMPER III Hand Tool
Repair Kit 679221-1 includes a replacement nut and a
variety of pins, rings, screws, and springs. If the dies
are damaged or worn excessively, they must be
replaced. Order the repair kit and replaceable parts
through your TE representative, or call 1-800-526-
5142, or send a facsimile of your purchase order to 1-
717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
11. REVISION SUMMARY
Since the previous release of this sheet, the following
changes were made:
? Added new information to bottom of Figure 1 table
and callout in Figure 2
? Changed information on last page
4 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58529-1 | TOOL PRO-CRIMPER II W/DIE SET |
| 210-5ESD | SWITCH EXTENDED ACTUATOR 5 SEC |
| 1-1579004-2 | TOOL CRIMP 10-12AWG SOLARLOK |
| 58514-1 | PROCRIMP TL W/DIE MR18-26 |
| 90870-1 | TOOL CRIMP .062 AWG 30 W/DIE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58517-1 | 制造商:TE Connectivity 功能描述:CST-100 Pro-Crimper II Hand Tool with Di |
| 58517-2 | 功能描述:折皱器 DIE SET RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58517-3 | 功能描述:折皱器 PRO CRIMP TOOL W.DIE SET RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58517-4 | 功能描述:冲压机与冲模 PRO-CRIMPER II DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58517-5 | 制造商:TE Connectivity 功能描述:SDE DIE SET, BENCH/BATTERY - Bulk |
发布紧急采购，3分钟左右您将得到回复。