- 您现在的位置：买卖IC网 > Datasheet目录601 > 58514-2 (TE Connectivity)DIE SET MR CONN USE WITH A9996 Datasheet资料下载
参数资料
| 型号： | 58514-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | DIE SET MR CONN USE WITH A9996 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, MR |
| 压接或电缆尺寸： | 18-26 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 242 (CN2011-ZH PDF) |
| 配用： | 350666-1-ND - CONN SOCKET 18-26AWG CRIMP TIN A25442-ND - CONN PIN GRND 18-26AWG TIN CRIMP A25445-ND - CONN SOCKET 24-26AWG GOLD CRIMP A25441-ND - CONN SOCKET 24-26AWG TIN CRIMP A25444-ND - CONN PIN 24-26AWG GOLD CRIMP A25446-ND - CONN PIN 18-26AWG GOLD CRIMP A25440-ND - CONN PIN 24-26AWG TIN CRIMP A14196-ND - CONN SOCKET 18-26AWG GOLD CRIMP A14197-ND - CONN SOCKET 18-26AWG TIN CRIMP A14198-ND - CONN PIN 18-26AWG GOLD CRIMP 更多... |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9949 |
408-9973
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop, as
shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles to
open and remove crimped contact.
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT
1. Remove the lockscrew from the ratchet
adjustment wheel.
NOTE
i
The crimped contact may stick in the crimping area,
but the contact can be easily removed by pushing
downward on the top of the locator (see Figure 3).
2. With a screwdriver, adjust the ratchet wheel from
the locator side of the tool (see Figure 5).
Screwdriver
7. Check the contact's crimp height as described in
Section 6, Crimp Height Inspection. If necessary,
adjust the crimp height as described in Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
RATCHET (Crimp Height) inspection is performed
through the use of a micrometer with a modified anvil,
commonly referred to as a crimp-height comparator.
TE does not manufacture or market crimp-height
comparators. Detailed information on obtaining and
using crimp-height comparators can be found in
instruction sheet 408-7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
Position Point ?
on Center of ?
Wire Barrel ?
Opposite ?
Seam ?
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
Figure 5
3. Observe the ratchet adjustment wheel. If a tighter
crimp is required, rotate the adjustment wheel
COUNTERCLOCKWISE to a higher-numbered
setting. If a looser crimp is required, rotate the
adjustment wheel CLOCKWISE to a lower-
numbered setting.
Modified ?
Anvil
“A”
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
WIRE SIZE
AWG (Max)
22
24
18
CRIMP SECTION
(Wire Size
Marking)
26-22
26-24
20-18
Figure 4
CRIMP HEIGHT
DIMENSION “A” AND
TOLERANCE (±)
.71 ±.05
[.028 ± .002]
.97 ±.05
[.038 ± .002]
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
8. MAINTENANCE
Ensure that the tool and dies are clean by wiping them
with a clean, soft cloth. Remove any debris with a
clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in the
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
Rev C
crimping dies, and store in a clean, dry area.
4 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 58517-4 | TOOL PRO-CRIMPER II DIE SET |
| 58519-1 | TOOL CRIMP F/OPTIC FSD STYLE |
| 58529-2 | TOOL DIE SET CRIMP TERMINAL |
| 58532-1 | TOOL FIBER OPTIC PRO CRIMPER III |
| 58541-2 | TOOL DIE FOR PRO-CRIMPER II |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5851421 | 制造商:Dialight 功能描述:LED Uni-Color Yellow 585nm 2-Pin |
| 585-1421 | 功能描述:LED替换灯-基于LED MIDG FLNG YELLOW 6V NON-POL. RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5851421F | 功能描述:LED Lamp Replacement Yellow Midget Flange 6V T - 1 3/4 制造商:dialight 系列:585 零件状态:停产 可更换灯:多小型法兰基座灯 大小/尺寸:T - 1 3/4 波长:585nm 电压 - 正向（Vf）（典型值）:6V 基底类型:小型法兰 颜色:黄 毫烛光等级:18mcd 配置:单一 应用:白炽灯替换件，指示灯 标准包装:5 |
| 585-1421F | 功能描述:LED替换灯-基于LED MIDG FLNG YELLOW 6V NON-POL. RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5851423 | 制造商:Dialight 功能描述:LED Uni-Color Yellow 585nm 2-Pin |
发布紧急采购，3分钟左右您将得到回复。