- 您现在的位置：买卖IC网 > PDF目录19193 > 58508-1 (TE Connectivity)TOOL CRIMP W/DIE 10-22AWG BUDGET PDF资料下载
参数资料
| 型号： | 58508-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP W/DIE 10-22AWG BUDGET |
| 特色产品： | SOLISTRAND?, Budget, and DIAMOND GRIP? Terminals and Splices |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，经济型 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接片和端子，10-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 382 (CN2011-ZH PDF) |
| 配用： | 331269-ND - CONN RECT TONGUE 10-12AWG #8 328522-ND - CONN SPADE FLNG 16-22AWG #10 327959-ND - CONN RECT TONGUE 10-12AWG #6 327953-ND - CONN RECT TONGUE 10-12AWG #5 326850-ND - CONN RING UNINS 16-22AWG #4 325195-ND - CONN SPADE UNINS 10-12AWG #8 324910-ND - CONN RING UNINS 10-12AWG #6 324604-ND - CONN SPADE FLNG 16-22AWG #2 323837-ND - CONN RING SLTD 16-22AWG #1/4 323835-ND - CONN RING SLTD UNINS 16-22AWG #6 更多... |
| 其它名称： | A31882 |
Figure 2
The die assembly features a wire anvil and a wire
crimper. Die retaining screws are used to secure the
dies in the tool frame.
7. To disassemble, close the tool handles until the
ratchet releases, remove the two die retaining
screws and slide the anvil and crimper out of the
tool jaws.
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil so that the crimping section
marked “22–16” faces outward when mounted in
the stationary jaw of the tool frame.
3. Insert the die retaining screw through the jaw
and through the anvil, and tighten the screw just
enough to hold the anvil in place. Do not tighten
the screw completely at this time.
4. Place the wire crimper so that the crimping
section marked “22–16” faces outward when
mounted in the moving jaw of the tool frame.
5. Insert the die retaining screw through the jaw
and through the crimper, and tighten the screw just
enough to hold the crimper in place. Do not tighten
the screw completely at this time.
Refer to the table in Figure 1 and select wire of the
specified size. Strip the wire to the length indicated in
Figure 1, taking care not to nick or cut wire strands.
Select an applicable terminal or butt splice and
identify the appropriate crimping section according to
the wire size markings on the dies. Proceed as
follows:
1. Squeeze tool handles together until the ratchet
releases and then allow the tool jaws to open fully.
2. Hold the tool so that the back (wire side) is
facing you. See Figure 3.
6. Carefully close the tool handles, making sure
that the anvil and crimper align properly. Continue
closing the tool handles until the ratchet in the tool
frame has engaged sufficiently to hold the anvil
and crimper in place, then tighten both die retaining
screws.
3. Holding the wire barrel, insert the terminal or
butt splice into the appropriate crimping section so
that the wire barrel seam faces the wire crimper
and the edge of the wire barrel is even with the
edge of the wire crimper.
相关PDF资料 |
PDF描述 |
|---|---|
| 210-10LPSTF | SWITCH SPST 10 SEC LOW PROFILE |
| 210-10MST | SWITCH RAISED ACTUATOR 10 SEC |
| 210-10LPST | SWITCH SPST 10 SEC TAPE SEAL |
| 210-10MSTFD | SWITCH RAISED ACTUATOR 10 SEC |
| 210-10LPSTFD | SWITCH SPST 10 SEC LOW PROFILE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58509-1 | 功能描述:折皱器 CRIMP HND TOOL W/DIE 22-14 12-10 AWG RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 5-850910-1 | 功能描述:标准环形连接器 FLANGED RECEPTACLE RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值: |
| 5-850911-1 | 功能描述:重负荷电源连接器 LGH-3 BULKHEAD REC RoHS:否 制造商:Hirose Connector 系列:PS2 产品类型:Connectors 位置/触点数量: 端接类型:Crimp 触点材料: 触点电镀:Gold 电压额定值: 电流额定值:300 A 附件类型: |
| 5-850912-1 | 制造商:TE Connectivity 功能描述:Conn LGH RCP 1 POS Solder ST Thru-Hole 1 Terminal 1 Port 制造商:TE Connectivity 功能描述:LGH-4 FLANGED RECEPT. - Bulk |
| 5850A510 | 制造商:ORTEL 功能描述: |
发布紧急采购，3分钟左右您将得到回复。