- 您现在的位置：买卖IC网 > Datasheet目录600 > 58433-4 (TE Connectivity)TOOL CRIMP F/OPTIC ST & SC Datasheet资料下载
参数资料
| 型号： | 58433-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP F/OPTIC ST & SC |
| 标准包装： | 25 |
| 系列： | Pro-Crimper III, OPTIMATE |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 光纤 - SC，ST |
| 特点： | 侧面插入，棘齿 |
| 其它名称： | A99105 |
i
PRO- CRIMPER III Hand Tool Frame Assembly 58433- 4
Cable
Crimp Eyelet
Figure 2
4. INSPECTION
4.1. Visual Inspection
1. Inspect the tool frame and die assembly on a
regular basis to ensure that they have not become
worn or damaged.
2. Inspect the crimping chamber of the die
assembly for flattened, chipped, worn, or broken
areas. If damaged, replace the die assembly.
4.2. Ratchet Inspection
The ratchet mechanism of the tool features an
adjustment wheel with eight settings. The ratchet
adjustment wheel controls the amount of handle
pressure exerted on the die assembly during the
crimping procedure. Although the ratchet is adjusted
and preset before shipping, general use and
subsequent wear may cause it to go out of
adjustment. It is recommended that the ratchet be
inspected, and adjusted if necessary as follows:
1. Measure the crimp height of a connector crimp
eyelet (shown in Figure 2), or a 4.75 [.187]
diameter solder rod, or a copper wire size 6 AWG
(having an insulation diameter of 4.11 [.162]).
408- 9671
If the crimp height measures 3.56+0.1 [.140+.004],
the ratchet is considered properly set.
If the crimp height is unacceptable, open the tool
handles, and remove the lockscrew (shown in
Figure 1) from the base of the ratchet adjustment
wheel (this will allow the wheel to be rotated). If the
crimped diameter is too large, turn the wheel
counterclockwise to the next higher notch (tighter).
If the crimped height is too small (which is
unlikely), turn the wheel clockwise to the next lower
notch (looser).
2. Re--install and tighten the lockscrew.
NOTE For other die assemblies, the ratchet adjustment
wheel might need to be adjusted in order to meet
the crimping specifications.
5. REPLACEMENT AND REPAIR
Order replacement parts through a TE representative,
or call 1--800--526--5142, or send a facsimile of your
purchase order to 1--717--986--7605, or write to:
CUSTOMER SERVICE (38--35)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG, PA 17105--3608
6. REVISION SUMMARY
Revisions to this instruction sheet include:
S Updated instruction sheet to corporate
requirements
S Added paragraph to Figure 1
S Changed button head socket cap screw and
hex head cap screw in Paragraph 4.2 to
lockscrew
2 of 2
Tyco Electronics Corporation
Rev D
相关PDF资料 |
PDF描述 |
|---|---|
| 58442-1 | TOOL HEAD ASSEMBLY RCPT MTA 100 |
| 58443-1 | TOOL HEAD ASSEMBLY MTA .156 |
| 58448-2 | CRIMP TOOL D-SUB TERMINALS |
| 58483-1 | TOOL SMB DIE SET CONN MIL TYPE |
| 58500-1 | TOOL CRIMP SMB RG/174 W/DIE SET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 584341-000 | 制造商:TE Connectivity 功能描述:WIRE/CABLE MISC. - Bulk 制造商:TE Connectivity 功能描述:381A115-4/42-0 |
| 58435-1 | 功能描述:冲压机与冲模 DIE FOR BNC CRIMP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58436-1 | 功能描述:冲压机与冲模 DIE SET RG58/59 HEX IS9159 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58436-2 | 功能描述:冲压机与冲模 DIE FOR BNC CRIMP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58436-3 | 功能描述:冲压机与冲模 DIE FOR BNC CRIMP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。