- 您现在的位置：买卖IC网 > Datasheet目录600 > 58425-3 (TE Connectivity)TOOL DIE SET COAX RG59 DB Datasheet资料下载
参数资料
| 型号： | 58425-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET COAX RG59 DB |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接手柄： | A9996-ND |
| 连接器类型： | BNC，TNC |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A1860 A1860-ND A9959 |
408-9657
Insert Center Contact
into Partially Closed
Crimping Dies
Center Contact
Slipped Over
Center Conductor
Flange on End of Center
Contact Butts Against Die
Flange on End
of Contact
Crimping Die
cut from the wire and replaced with a new one. Do
NOT reterminated contact or ferrules.
Ferrule
(Ref)
Figure 2
4. CRIMPING PROCEDURE
4.1. Center Contact
1. Prepare the connector and the cable according to
the instructions packaged with the connector.
2. Slide the center contact onto the center
conductor of the cable; then insert the contact
assembly into the center contact crimp section of
Figure 3
CAUTION Damaged product should not be used. If a
damaged contact or ferrule is evident, it should be
!
5. INSPECTION
5.1. Visual Inspection
Inspection of the crimping dies should be made on a
regular basis to ensure that they have not become
worn or damaged. Inspect the crimp sections for
flattened, chipped, worn, or broken areas. If damage
or abnormal wear is evident, the dies must be
NOTE
i
Make sure that the flange on the end of the center
contact butts against the crimping die. See ?
replaced. Refer to Section 6, PARTS REPLACEMENT.
Crimping Ferrule
3. Crimp the center contact by holding the cable in
place; then close the tool handles until the ratchet
releases.
4.2. Ferrule
1. Insert the crimped center contact into the
connector body until the cable dielectric butts
against the dielectric inside of the connector body.
Crimping Die
(Ref)
Shoulder on
Connector Body
Butts Against Die
The flared braid will then fit around the support
sleeve of the connector body.
2. Slide the ferrule forward over the braid until the
ferrule butts against the shoulder on the connector
body.
3. Place the ferrule on the appropriate anvil of the
die assembly so that the shoulder on the connector
4. Holding the assembly in place, close the tool
handles until the ratchet releases.
Rev E
Typical RF
Connector
(Ref)
Figure 4
Ferrule on Anvil
of Crimping Die
2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 58430-1 | TOOL REPAIR .050 SERIES |
| 58432-1 | TOOL DIE SET |
| 58433-4 | TOOL CRIMP F/OPTIC ST & SC |
| 58442-1 | TOOL HEAD ASSEMBLY RCPT MTA 100 |
| 58443-1 | TOOL HEAD ASSEMBLY MTA .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 584259-000 | 制造商:TE Connectivity 功能描述:Cable Accessories Transition Semi-Rigid Modified Polyolefin 制造商:TE Connectivity 功能描述:322A112-3/86-0 - Bulk 制造商:TE Connectivity 功能描述:BOOT MOLDED |
| 58426HV | 功能描述:速度传感器 FMD MS3106A RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
| 58426HVA30 | 功能描述:速度传感器 ELECTRO RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
| 58426LV | 功能描述:速度传感器 FMD 5V MS3106A RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
| 58426LVA30 | 功能描述:速度传感器 ELECTRO RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
发布紧急采购，3分钟左右您将得到回复。