- 您现在的位置：买卖IC网 > Datasheet目录600 > 525693 (TE Connectivity)TOOL HAND SOLIS STRATO 10-22AWG Datasheet资料下载
参数资料
| 型号： | 525693 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND SOLIS STRATO 10-22AWG |
| 标准包装： | 10 |
| 系列： | Certi-Crimp, Solistrand, Strato-Therm |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接片和端子，10-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 736014-ND - CONN UNINSUL PIN WIRE 4AWG 53112-1-ND - CONN RELAY TERM FLAG 16-20AWG 8-330368-1-ND - CONN BUTT SPLICE UNINS 14-16AWG 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 2-323683-1-ND - CONN RING 10-12AWG #1/4 ORANGE 322824-ND - CONN BUTT SPLICE UNINS 14-16AWG 2-321896-2-ND - CONN RING 16-22AWG #10 ORANGE 1-34108-1-ND - CONN RING UNINS 16-22AWG #8 8-31819-6-ND - CONN BUTT SPLICE UNINS 14-16AWG 8-53555-1-ND - CONN SPADE 22-16AWG #2 SOLIS 更多... |
408-1542
Terminals and Splices Can Also Be Rotated 180° with the Seam Toward the Nest
Figure 3
NOTE
i
5.2. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with SAE 20 motor oil as follows:
Tools used in daily production - lubricate daily ?
Tools used daily (occasional) - lubricate weekly ?
Tools used weekly - lubricate monthly
Wipe excess oil from tool, particularly from crimping
area. Oil transferred from the crimping area onto
certain terminations may affect the electrical
characteristics of an application.
5.3. Periodic Inspection
1. The tool should be immersed (handles
partially closed) in a reliable commercial
degreasing compound to remove accumulated
dirt, grease, and foreign matter.
2. Close tool handles until ratchet releases and
then allow them to open freely. If they do not
open quickly and fully, the spring is defective and
must be replaced. See Section 6,
REPLACEMENT AND REPAIR.
3. Inspect head assembly for worn, cracked, or
broken jaws. Refer to Figure 5. If damage is
evident, return the tool to TE for evaluation and
repair. See Section 6, REPLACEMENT AND
REPAIR.
5.4. Gaging the Crimping Chambers
This inspection requires the use of a plug gage
conforming to the dimensions provided in Figure 6
and Figure
TE does not manufacture or market these gages. To
gage the crimping chambers, proceed as follows:
Remove traces of oil or dirt from the crimping
chambers and plug gage.
4. Close the tool handles until it is evident that
the jaws have bottomed; then hold in this
position. Do NOT force the jaws beyond initial
contact.
5. Align the GO element with the crimping
chamber. Push element straight into the
crimping chamber without using force. The GO
element must pass completely through the
crimping chamber.
6. Align the NO-GO element and try to insert it
straight into the same crimping chamber. The
NO-GO element may start entry, but must not
pass completely through the crimping chamber.
The jaws in Tools 49935 and 574573 are not
symmetrically located; make sure that the tool
conforms to the symmetry requirements shown in
Figure 8.
If the crimping chambers conforms to the gage
inspection, the tool is considered dimensionally
correct, and should be lubricated with a THIN coat of
any good SAE 20 motor oil. If not, the tool must be
returned for further evaluation and repair. Refer to
Section 6, REPLACEMENT AND REPAIR.
For additional information regarding the use of a plug
gage, refer to Instruction Sheet 408-7424. ?
?
?
Rev N
Tyco Electronics Corporation
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 53200C | XFRMR CURR SENSE 10A 1:200 SMD |
| 532925-2 | TOOL HDI ALIGNMENT 540POS |
| 535072-1 | TOOL EURO TYPE C CONN INSERT |
| 539758-2 | DIE 2,8 TAB+EDS |
| 539960-1 | EXTRACTION TOOL FOR AP-963711-1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 52569-4 | 功能描述:TERM,COPALUM R 500-600 MCM 1/2 制造商:te connectivity aerospace, defense and marine 系列:* 零件状态:新产品 标准包装:5,000 |
| 525696 | 功能描述:手工工具 CAST JAW INDENTER - INSUL RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 5256A20004A | 制造商:LG Corporation 功能描述:Muffler |
| 5256A30003D | 制造商:LG Corporation 功能描述:Muffler |
| 5256A30003J | 制造商:LG Corporation 功能描述:Muffler |
发布紧急采购，3分钟左右您将得到回复。