- 您现在的位置：买卖IC网 > PDF目录33783 > 44608P40 (ON SEMICONDUCTOR) Few External Components Reliable Flexible GreenLine Very High Voltage PWM Controller PDF资料下载
参数资料
| 型号： | 44608P40 |
| 厂商： | ON SEMICONDUCTOR |
| 英文描述： | Few External Components Reliable Flexible GreenLine Very High Voltage PWM Controller |
| 中文描述： | 很少的外部元件的可靠灵活二七二三六七六七高电压PWM控制器 |
| 文件页数： | 13/16页 |
| 文件大小： | 266K |
| 代理商： | 44608P40 |
MC44608
http://onsemi.com
6
In stand–by mode, this current can be lowered as due to the
activation of a 200
A current source:
Ipk
max
*stby +
1
* (Rcs(kW) 0, 2)
Rsense(W)
(A)
Figure 2. Current Sense
+
–
Switching Phase
1 V
STAND–BY
10
&
2
Isense
L.E.B.
Overcurrent
OC
200 A
m
START–UP
Comparator
Rcs
Rsense
The current sense input consists of a filter (6k
W, 4pF) and
of a leading edge blanking. Thanks to that, this pin is not
sensitive to the power switch turn on noise and spikes and
practically in most applications, no filtering network is
required to sense the current.
Finally, this pin is used:
– as a protection against over currents (Isense > I)
– as a reduction of the peak current during a Pulsed Mode
switching phase.
The overcurrent propagation delay is reduced by
producing a sharp output turn off (high slew rate). This
results in an abrupt output turn off in the event of an over
current and in the majority of the pulsed mode switching
sequense.
Demagnetization Section
The MC44608 demagnetization detection consists of a
comparator designed to compare the VCC winding voltage
to a reference that is typically equal to 50mV.
This reference is chosen low to increase effectiveness of
the demagnetization detection even during start–up.
A latch is incorporated to turn the demagnetization block
output into a low level as soon as a voltage less than 50 mV
is detected, and to keep it in this state until a new pulse is
generated on the output. This avoids any ringing on the input
signal which may alter the demagnetization detection.
For a higher safety, the demagnetization block output is
also directly connected to the output, which is disabled
during the demagnetization phase.
The demagnetization pin is also used for the quick,
programmable OVP. In fact, the demagnetization input
current is sensed so that the circuit output is latched off when
this current is detected as higher than 120
A.
Figure 3. Demagnetization Block
&
1
DMG
> 24 A
Output
Current Mirror
Oscillator Buffer
+
–
Idemag
50/20 mV
>120 A
m
Demag
RQ
S
DMG
This function can be inhibited by grounding it but in this
case, the quick and programmable OVP is also disabled.
Oscillator
The MC44608 contains a fixed frequency oscillator. It is
built around a fixed value capacitor CT succesively charged
and discharged by two distinct current sources ICH and
IDCH. The window comparator senses the CT voltage value
and activates the sources when the voltage is reaching the
2.4V/4V levels.
Figure 4. Oscillator Block
+
–
from Demag
4 V
2.4 V
&
Window
OSC
ICH
comp
DMG
SDCH
IDCH
logic block
SCH
Clock
CT
The complete demagnetization status DMG is used to
inhibit the recharge of the CT capacitor. Thus in case of
incomplete transformer demagnetization the next switching
cycle is postpone until the DMG signal appears. The
oscillator remains at 2.4V corresponding to the sawtooth
valley voltage. In this way the SMPS is working in the so
called SOPS mode (Self Oscillating Power Supply). In that
case the effective switching frequency is variable and no
longer depends on the oscillator timing but on the external
working conditions (Refer to DMG signal in the Figure 5).
相关PDF资料 |
PDF描述 |
|---|---|
| 44620-0001 | Phone Connector,PCB Mnt,8 Contacts,PIN,PC TAIL Terminal,LOCKING MECH |
| 44620-0002 | Modular Jack; No. of Contacts:8; No. of Ports:1; Connector Body Material:Nylon; Mounting Type:PC Board; Series:RJ45 RoHS Compliant: Yes |
| 44620-0003 | RJ45 Inv Modjack w/Keepout Featureoffset |
| 44661-0001 | Modjack RA Compact Cat 5 PTH Shielded RoHS Compliant: Yes |
| 44661-0002 | Modular Connector; No. of Contacts:8; No. of Ports:1; Body Material:PA Polyamide (Nylon), Glass-filled; Color:Black; Contact Termination:Through Hole; Mounting Type:Thru-Hole; Body Style:Right Angle; Current Rating:1.5A RoHS Compliant: Yes |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4460B5CBS | 制造商:Texas Instruments 功能描述: |
| 4460BCBS | 制造商:Texas Instruments 功能描述:- Trays |
| 4460CPCE10D434 | 功能描述:WIRELESS RF DEVEL KIT 制造商:silicon labs 系列:EZRadioPRO? 零件状态:在售 类型:收发器 频率:434MHz 配套使用产品/相关产品:Si4460 所含物品:板 标准包装:1 |
| 4460CPCE27E169S | |
| 4460CPCE30E915S | 功能描述:WIRELESS RF DEVEL KIT 制造商:silicon labs 系列:EZRadioPRO? 零件状态:在售 类型:收发器 频率:915MHz 配套使用产品/相关产品:Si4460 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。