- 您现在的位置：买卖IC网 > Datasheet目录648 > 35130 (Desco)TESTER CONT 3V 0-10 OHMS Datasheet资料下载
参数资料
| 型号： | 35130 |
| 厂商： | Desco |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | TESTER CONT 3V 0-10 OHMS |
| 标准包装： | 1 |
| 系列： | Menda® |
| 工具类型： | 连续性测试器 |
| 适用于相关产品： | 现场测试 |
ASSEMBLY OF MODEL 35100 FOR TESTING
POWERED CIRCUITS
When assembled without batteries, the model 35100
circuitracer can be used to test powered circuits.
Assembly for testing 1-3 volt circuits.
1. Unscrew transparent probe window from handle.
2. Insert the incandescent lamp into the spring-connector
and drop into the probe window with spring touching
the back end of the probe. Center contact of lamp will
point toward threaded end of probe window.
3. Push the lead wire and pull down slightly until three
pointed washer rests on ledge inside of handle. Hold
tension on back of lead wire with hand as illustrated
above to keep assembly in place.
4. Screw transparent probe window back on handle so
that the center contact of lamp makes contact with
lead wire.
5. Test lamp by applying correct supply voltage across
clip and probe before starting circuit testing.
Assembly for testing 60-600 volt circuits.
1. Unscrew transparent probe window from handle.
2. Insert the neon lamp into the probe window so that
one contact rests against the back end of the probe.
3. Push the lead wire and pull down slightly until the
three pointed washer rests on ledge inside of the
handle. Hold tension on back of lead wire with hand
as illustrated above to keep assembly in place.
4. Screw transparent probe window back on handle so
that the contact of neon lamp makes contact with lead
wire.
5. Test lamp by applying a supply voltage in excess of
60 volts across clip and probe before starting circuit
testing.
ASSEMBLY OF MODELS 35130, AND 35135
Models 35130 and 35135 are powered by 2 AAA
batteries. They are designed to test continuity on
unpowered circuits.
1. Unscrew probe assembly.
2. Insert battery(s) into handle so that positive end of
battery(s) points towards probe window.
3. Screw probe window onto handle. Touch clip to probe
end to be sure circuitracer is working properly.
Troubleshooting Tip:
Please check to verify the battery is working. If the
battery is working properly, please check the transparent
probe window. If there is debris or small particles it may
interfere with the connection. Use compressed air to
blow any debris or particles off the transparent probe
window. You can then replace the battery back in and
test the circuitracer again.
Limited Warranty
Menda expressly warrants that for a period of one (1) year from
the date of purchase, Menda Circuitracer ? units will be free
of defects in material (parts) and workmanship (labor). Within
the warranty period, the product will be tested, repaired, or
replaced at Menda’s option, free of charge. Call our Customer
Service Department at 909-627-2453 for a Return Material
Authorization (RMA) and proper shipping instructions and
address. Include a copy of your original packing slip, invoice, or
other proof of purchase date. Any unit under warranty should be
shipped prepaid to the Menda factory. Warranty repairs will take
approximately two weeks.
If your unit is out of warranty, call Customer Service at
909-627-2453 for a Return Material Authorization (RMA) and
proper shipping instructions and address. Menda will quote
repair charges necessary to bring your unit up to factory
standards.
Warranty Exclusions
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU
OF ALL OTHER PRODUCT WARRANTIES, EXPRESSED AND
IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY
DISCLAIMED. The express warranty will not apply to defects or
damage due to accidents, neglect, misuse, alterations, operator
error, or failure to properly maintain, clean or repair products.
Limit of Liability
In no event will Menda or any seller be responsible or liable for
any injury, loss or damage, direct or consequential, arising out
of the use of or the inability to use the product. Before using,
users shall determine the suitability of the product for their
intended use, and users assume all risk and liability whatsoever
in connection therewith.
Model 35130
Model 35135
Assembly of Continuity Circuitracers ? .
3651 Walnut Avenue, Chino, CA 91710
Phone: (909) 627-2453 ? Fax (909) 755-8848 ? Web Site: www.MendaPump.com
TB-4005 Page 2 of 2
? 2011 DESCO INDUSTRIES INC.
Employee Owned
相关PDF资料 |
PDF描述 |
|---|---|
| 353377-7 | SQUIB CONN HSG YELLOW |
| 353378-7 | SQUIB CONN HSG YELLOW |
| 353379-2 | SQUIB CONN FERRITE |
| 353838-1 | SEAT BELT FPC COVER HSG ASSY |
| 353840-1 | SEAT BELT FPC PLATE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 35-130 | 制造商:GC Electronics 功能描述:SPDT ON-ON BAT TOGGLE SWITC 制造商:GC Electronics 功能描述:Switch Toggle ON ON SPDT Bat Toggle Screw 20A 277VAC Panel Mount with Threads |
| 35-1300 | 制造商:GC Electronics 功能描述:Switch Rocker ON OFF SPST Quick Connect Round Rocker 10A 250VAC |
| 3513-00 | 功能描述:EVAK KIT FOR 3513 RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:UltraCMOS™ 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| 351-3003 | 功能描述:标准LED-通孔 T-1 GRN DIFF LED RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube |
| 35-1300-B37R | 制造商:GC Electronics 功能描述: |
发布紧急采购，3分钟左右您将得到回复。