- 您现在的位置：买卖IC网 > Datasheet目录596 > 312253-2 (TE Connectivity)CONN SMA DIE/SET 50OHM RG402 2PC Datasheet资料下载
参数资料
| 型号： | 312253-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | CONN SMA DIE/SET 50OHM RG402 2PC |
| 标准包装： | 1 |
| 压接或电缆尺寸： | RG/U-402 |
| 压接手柄： | A9966-ND |
| 连接器类型： | SMA |
| 产品目录页面： | 453 (CN2011-ZH PDF) |
| 配用： | 413249-1-ND - CONTACT JACK COAX 405SR 413242-1-ND - CONTACT PLUG BLIND MATE STR GOLD |
| 相关产品： | A9966-ND - TOOL SMA CRIMP FRAME ONLY |
| 其它名称： | A9964 |
408-6788
i NOTE Make sure that the shoulders of the conforming block
Spacer Used
with SMA Plugs
Cable Bending
Dummy Jack
NOTE
bear on the bottom surface of the tool holder BEFORE
applying pressure in the vise.
7. Tighten the vise to force the conforming block into
the slot. Continue to tighten until the legs of the tool
Figure 14
Bending RG-402 Cable to 6.35mm [.250 in.] Radius or
RG-405 Cable to 3.18mm [.125 in.] Radius
Tool Holder
Bend Segment
Oriented Properly
Apply Finger Pressure
Plugs Screwed
onto Tool Holder
Figure 15
Bending RG-402 Cable to 3.18 mm [.125 in.] Radius
holder prevent further movement of the vise jaws.
8. Remove the assembly from the vise, and
unscrew the plug from the fixture.
9. Remove the conforming block and bend
segment.
8.3. To Make 1.57 mm [.062 in.] Bends on RG-405 Cable
It is recommended that a special kit be used to make
1.57 mm [.062 in.] bends on RG-405 cable. Kit
220224-2 includes a limiting pin, a 90° bend tool body
assembly, a 90° bend segment, and a conforming
block. The figures referenced for the 6.35 mm
[.250 in.] and 3.18 mm [.125 in.] bends will assist in
making the 1.57 mm [.062 in.] bends. These steps are
recommended:
1. Make the 3.18 mm [.125 in.] radial bend as
described in Paragraph 8.1, and remove the plug
from the tool holder.
2. Replace the 3.18 mm [.125 in.] bend segment
with the special 1.57 mm [.062 in.] bend segment,
which is a part of Kit 220224-2.
3. Re-attach the plug to the dummy jack of the tool
holder.
Tongue
Cable Previously
Formed to 6.35
[.250] Radius
Bend
Tool Holder
3.18 [.125]
Radius Bend
Segment
Limiting Pin
Conforming
Block Shoulder
4. Place the special 1.57 mm [.062 in.] conforming
block over the cable with the tongue of the block in
the tool holder slot. The conforming block is part of
Kit 220224-2.
5. Insert the limiting pin and slide the block against
the tool holder.
6. Place the assembly in a vise with a 69.85 mm
[2.75 in.] opening.
7. Remove the assembly from the vise, and
unscrew the plug from the fixture.
8. Remove the assembly from the vise, and
unscrew the plug from the fixture.
9. Remove the special conforming block and special
bend segment.
9. MAINTENANCE AND INSPECTION
Legs of Tool Holder Prevent Further
Movement of Vise Against Conforming Block
Figure 16
6. Place the assembly in a vise with a 69.85 mm
[2.75 in.] opening.
Rev L
Hand Crimping Tool and Cable Preparation Kit
59981-1 is inspected before shipment. The tool and kit
should be inspected immediately upon arrival to
ensure that they have not been damaged during
shipment, and that they perform according to the
criteria described in this sheet. If the tool and kit are
damaged upon arrival, retain the shipping container,
file a claim with the carrier, and notify TE immediately.
9 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 318837-1 | EXTRACTION TOOL .093 CONN |
| 3430-1000 | DISCRETE WIRE INSERTION TOOL |
| 3430-2000 | DISCRETE WIRE HAND TOOL |
| 3430-4000 | HEADER ROLL PIN INSERTER |
| 350-MX23-2 | TOOL CRIMP FOR MX23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 31226103 | 制造商:METZ CONNECT USA 功能描述: |
| 31226106 | 制造商:METZ CONNECT USA 功能描述: |
| 31226108 | 制造商:METZ CONNECT USA 功能描述: |
| 31226110 | 制造商:METZ CONNECT USA 功能描述: |
| 31-2264 | 制造商:AMPHENOL 制造商全称:AMPHENOL 功能描述:TNC Jacks |
发布紧急采购，3分钟左右您将得到回复。