参数资料
| 型号： | 2891314 |
| 厂商： | Phoenix Contact |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | SWITCH ETHERNET 6/RJ45-2SC F/OPT |
| 标准包装： | 1 |
| 类型： | 以太网 |
| 特点： | 6 个端口 |
| 其它名称： | 277-2446 2891314-ND FLSWITCHSFN6TX/2FX |
FL SWITCH SFN…
6
Installation
6.2
Removal
CAUTION:
1.
Insert a suitable tool (e.g., needle-nose pliers) into the
arresting latch and pull it down.
Only qualified personnel may start up and operate
this device. Qualified personnel are persons
authorized to start up, ground and mark devices,
systems, and equipment according to the
standards of safety technology.
2.
3.
6.3
Pull the module slightly away from the mounting
surface.
Lift the module from the rail.
Power Connection
NOTE:
The FL SWITCH SFN… module is designed for
SELV and PELV operation according to
The switch is designed for SELV and PELV operation at
+24 V DC according to IEC 61140/EN 61140. Only SELV
and PELV according to the defined standards may be used
for supply purposes.
IEC 61140/EN 61140.
Snapping the switch onto a grounded DIN rail connects it to
WARNING:
A.)THIS EQUIPMENT IS SUITABLE FOR USE IN
CLASS I, ZONE 2, GROUPS A, B, C, AND D OR
NON- HAZARDOUS LOCATIONS ONLY.
B.) WARNING - EXPLOSION HAZARD -
the ground potential. In an environment particularly prone to
EMI, noise immunity can be increased by an additional low-
impedance connection to functional earth ground.
SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, ZONE 2.
C.) WARNING - EXPLOSION HAZARD - DO
NOT DISCONNECT EQUIPMENT UNLESS
POWER HAS BEEN SWITCHED OFF OR THE
AREA IS KNOWN TO BE NON-HAZARDOUS.
Install the FL SWITCH SFN… on a clean DIN rail. To avoid
contact resistance use only clean, corrosion-free rails that
+
–
meet the EN 50022 standard. End clamps should be
mounted on both sides of the module to stop the modules
from slipping on the rail.
US GND
6.1
1.
2.
3.
NOTE:
Connect the DIN rail to protective earth ground
using a grounding terminal block. The modules
are grounded when they are snapped onto the
rail. Connect protective earth ground with low
impedance. 1000 Mbps switches have a
protective ground connecting screw on top.
Assembly
Place the module onto the DIN rail from above. The
upper holding keyway must be hooked onto the top
edge of the DIN rail.
Push the module from the front towards the mounting
surface.
Once the module has been snapped on properly, check
that it is fixed securely on the rail.
Figure 3
FL SWITCH SFN…TX… power connection
2732_en_D
PHOENIX CONTACT
8
相关PDF资料 |
PDF描述 |
|---|---|
| OSTYK55206030 | CONN BARRIER STRIP 6CIRC 11MM |
| OSTYK50606330 | CONN BARRIER STRIP 6CIRC 9.50MM |
| OSTYK22108030 | CONN BARRIER STRIP 8CIRC 6.35MM |
| G6KU-2F-RF DC24 | RELAY RF DPDT 1A 24V |
| GBSAX-3 | TERM BARRIER 3CIRC SGL ROW .438 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2891315 | 功能描述:FO CONVERTER SC DUPLEX 制造商:phoenix contact 系列:- 包装:* 零件状态:在售 类型:非受控 配置:固定式 铜端口:1 铜类型:10/100 光纤端口:1 光纤类型:100BASE-FX（多模） SFP/XFP 端口:- 特性:- 距离:10km MTU:- 电压 - 输入:12 ~ 48VDC 连接器类型:RJ45，SC 安装类型:DIN 轨道 侵入防护:IP20 工作温度:-40°C ~ 75°C 标准包装:1 |
| 2891316 | 功能描述:FO CONVERTER ST DUPLEX 制造商:phoenix contact 系列:- 包装:* 零件状态:在售 类型:非受控 配置:固定式 铜端口:1 铜类型:10/100 光纤端口:1 光纤类型:100BASE-FX（多模） SFP/XFP 端口:- 特性:- 距离:10km MTU:- 电压 - 输入:12 ~ 48VDC 连接器类型:RJ45，ST 安装类型:DIN 轨道 侵入防护:IP20 工作温度:-40°C ~ 75°C 标准包装:1 |
| 2891317 | 功能描述:FO CONVERTER SC DUPLEX 制造商:phoenix contact 系列:- 包装:* 零件状态:在售 类型:非受控 配置:固定式 铜端口:1 铜类型:10/100 光纤端口:1 光纤类型:100BASE-FX（单模） SFP/XFP 端口:- 特性:- 距离:20km MTU:- 电压 - 输入:12 ~ 48VDC 连接器类型:RJ45，SC 安装类型:DIN 轨道 侵入防护:IP20 工作温度:-40°C ~ 75°C 标准包装:1 |
| 2891318 | 功能描述:FO CONVERTER SC DUPLEX 制造商:phoenix contact 系列:- 包装:* 零件状态:在售 类型:非受控 配置:固定式 铜端口:1 铜类型:10/100 光纤端口:1 光纤类型:100BASE-FX（单模） SFP/XFP 端口:- 特性:- 距离:40km MTU:- 电压 - 输入:12 ~ 48VDC 连接器类型:RJ45，SC 安装类型:DIN 轨道 侵入防护:IP20 工作温度:-40°C ~ 75°C 标准包装:1 |
| 2891320 | 功能描述:FO CONVERTER SC DUPLEX 制造商:phoenix contact 系列:- 包装:* 零件状态:在售 类型:非受控 配置:固定式 铜端口:1 铜类型:10/100 光纤端口:1 光纤类型:100BASE-FX（多模） SFP/XFP 端口:- 特性:- 距离:10km MTU:- 电压 - 输入:12 ~ 48VDC 连接器类型:RJ45，SC 安装类型:DIN 轨道 侵入防护:- 工作温度:0°C ~ 60°C 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。