参数资料
| 型号： | 2300986 |
| 厂商： | Phoenix Contact |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | CONN RECEPTACLE D-SUB 37POS |
| 标准包装： | 1 |
| 系列： | SUBCON |
| 连接器类型： | D-Sub |
| 位置数： | 37 |
| 行数： | 2 |
| 外壳尺寸，连接器布局： | 4（DC，C） |
| 触点类型：： | 信号 |
| 连接器类型： | 插座，母形插口 |
| 安装类型： | 自由悬挂 |
| 法兰特点： | 线缆侧；公型起重螺钉（4-40） |
| 端子： | 端接块 |
| 特点： | 缆线夹，屏蔽 |
| 工作温度： | -20°C ~ 75°C |
| 额定电压： | 60V |
| 额定电流： | 1A |
| 体座材料： | 丙烯腈苯乙烯丁二烯共聚物（ABS），带金属镀层 |
| 其它名称： | 2300986-ND 277-2430 Q5144265 SUBCON37/F-SH |
7
Assembly Procedures
7.1 Left-side Cable Entry
1. Place the printed circuit board onto the PC board guide pins of housing-half
“B” (see Figure 8).
2. Lay the cable, previously prepared, on housing-half “B”' so that the shielded
end of the cable is about 10 mm (3/8 in.) in from the forward cable-entry hole
of the housing.
3. Terminate conductors using the guidelines shown in Figure 8. For cable
containing over 20 conductors, we also recommend installing one of the con-
nector thumbscrews after about one-half of the conductors have been termi-
nated.
CAUTION
To prevent conductors from becoming damaged during assembly
of the two housing halves, make sure conductors are clear from the
mating surfaces..
SUBCON
Housing-half “B”
Connector
Thumbscrew
37 3
To prevent the upper housing
from damaging the wires during
assembly, keep wires away from
housing in this area
6 35 3
43
3 32
31 3
0 29
2
8 27
26
25 2
4 23
22 2
1 20
PC Board Guide
Pin (typical both
sides)
2
20
21
22
23
24
1668A016
25
26
10
28
29
13
31
32
16
PC Board Guide
34
Forward Cable
Entry Position
of Housing
19
18
37
17
36
35
15
33
1
3
4
5
6
7
8
9
11 27
12
14 30
Pin Alignment Hole
(typical both sides)
360° Shielded Strain Relief/
Cable Ground Clamp
Ground the SUBCON Housing
to the Cable Using the Braided
Shield or Drain Wire of Cable
Note
For cables containing over 20 wires,
place one-half of the wires above the
connector thumbscrew and one-half of
the wires below the thumbscrew
Figure 8.
Assembling Connector for Left-side Cable Entry
相关PDF资料 |
PDF描述 |
|---|---|
| 2307-96MMX55M | TAPE MASKING NATURAL 96MM X 55M |
| 2308-72MMX55M | TAPE MASK PERFORMANCE 72MM X 55M |
| 231-72MMX55M | TAPE PAINT MASKING 72MM X 55M |
| 2313067 | ANALOG MODEM 3-WAY 24VDC DIN |
| 232-96MMX55M | TAPE MASKING HI-PERFORM 96MMX55M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 230-09-AL-832 | 制造商:PROMPTUS 功能描述: |
| 230-09-AL-832-B2 | 制造商:PROMPTUS 功能描述: |
| 2300A | 制造商:Marinco Electrical Group 功能描述: |
| 2300-A | 功能描述:旋钮和转盘 RoHS:否 制造商:Davies Molding 材料:Phenolic 设计:Set Screw 轴尺寸:0.25 in 直径:3/4 in 颜色:Black 指示器型式:Line |
| 2300-A (WITH BRASS INSERT) | 功能描述:旋钮和转盘 W/BRASS INSERT NO IND LINE RoHS:否 制造商:Davies Molding 材料:Phenolic 设计:Set Screw 轴尺寸:0.25 in 直径:3/4 in 颜色:Black 指示器型式:Line |
发布紧急采购，3分钟左右您将得到回复。