- 您现在的位置：买卖IC网 > Datasheet目录595 > 19286-0065 (Molex Connector Corporation)TOOL DIELESS HEAD CRIMPER Datasheet资料下载
参数资料
| 型号： | 19286-0065 |
| 厂商： | Molex Connector Corporation |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | TOOL DIELESS HEAD CRIMPER |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 1 |
| 系列： | DLH-Putt 泵 |
| 工具类型： | 台式压机，气动式 |
| 适用于相关产品： | 接片和端子，500MCM-8 AWG |
| 特点： | 侧面插入 |
| 配用： | 0191540049-ND - BUTT SPLICE BZD INSULKRIMP 0191540048-ND - BUTT SPLICE BZD INSULKRIMP 0191540047-ND - 6 TO 8 AWG BUTT SPLICE VYL.INS 0192210382-ND - BATTERY CABLE LUG (BCL-4038) 0192210394-ND - BATTERY CABLE LUG (BCL-10516) 0192210381-ND - BATTERY CABLE LUG (BCL-3038) 0192210396-ND - BATTERY CABLE LUG (BCL-1516) 0192210397-ND - BATTERY CABLE LUG (BCL-2012) 0192210423-ND - BATTERY CABLE LUG (BCL-1014) 0192210425-ND - BATTERY CABLE LUG (BCL-610) 更多... |
| 其它名称： | 019286-0065 019286-0065-C 019286-0065-E 0192860065 0192860065-C 0192860065-E 19286-0065-C 19286-0065-E 19286-0065-ND 192860065 192860065-C 192860065-E WM6455 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
DLH-Putt Pump Dieless Head Crimper
5.1 Lubrication
WARNING: Any repair or servicing, which
requires dismantling the pump must be
performed in a dirt-free environment by a
qualified technician.
CAUTION: Always disconnect power supply
before all maintenance
If the pump is operated on a continuous duty cycle for
extended periods, the manufacturer recommends an
automatic air line oiler be installed in the air inlet as
close to the pumping unit as possible.
5.4 Refilling The Reservoir
CAUTION: Always disconnect power supply
before all maintenance
1. If additional oil must be added to the reservoir,
use only an approved high grade hydraulic oil
such as OTC 16355 (215 SSU @ 100° F).
2. Clean the entire area around the filler plug
before adding oil to the reservoir.
3. Remove the filler plug and insert a clean funnel
with filter.
4. The ram must be fully retracted and the air
supply disconnected when adding the oil to the
reservoir.
Set the unit to feed approximately 1 drop of oil per
minute into the system. Use SAE No. 10 oil.
5.2 Bleeding Air From The System
During the initial moments of activation or after
prolonged use, a significant amount of air may
5.5 Venting the Reservoir
To improve oil delivery and increase useable oil
capacity, vent the reservoir by removing the vent
screw from the filler plug before using the pump.
See Figure 5-1.
accummulate within the hydraulic system. This
entrapped air may cause the cylinder to respond slowly
or behave in an unstable manner.
To remove the air, run the system through several
cycles (extending and retracting the ram) free of any
load. The rams must be at a lower level than the pump
to allow air to be released through the pump reservoir.
VENT
5.3 Inspecting The Hydraulic Fluid Level
SCREW
Figure 5-1
CAUTION: Always disconnect power supply
before all maintenance
1. Check the oil level in the reservoir after every 10
hours of use.
2. The oil level should come to within 1/2" of the
filler plug with all hoses attached.
3. Drain and replenish the reservoir with an
approved, high-grade hydraulic oil such as OTC
16355 after every 300 hours of use.
Hoses: Hydraulic hoses on this unit carry a
rating of 10,000 PSI.
Replacement hoses must carry the same rating.
5.6 Priming the Pump Unit
If the pump unit must be primed, perform the
following procedure:
1. Depress the release end of the pedal while
holding down the air intake valve with a
flathead screwdriver. See Figure 1-3. The air
intake valve is located directly under the pedal
in the area marked PUMP. This "button" is
depressed simultaneously with the RELEASE
area of the pedal during priming.
Doc. No: TM-192860065
Revision: F
Release Date: 05-12-04
Revision Date: 05-13-09
UNCONTROLLED COPY
Page 20 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| 1976230-1 | HYDRAULIC CRIMPING HEAD ASS Y |
| 1981944-1 | CABLE CAT5E STRIPPER |
| 2-1105870-8 | TOOL DIE SET - HSK,HSM,HSS CONT |
| 2-1579007-1 | EXTRACTION TOOL |
| 2-1611461-1 | TRANSFORMER OUTLINE 7/8 120VAC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 19286-0067 | 制造商:MOLEX 功能描述:ETC TOOL |
| 19286-0070 | 功能描述:手工工具 1/8 BALL HUSKIE#40- 20 (HHLS) (192860070 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 19286-0071 | 功能描述:手工工具 HEAD HUSKIE # 510K-0 -03 HHLS (192860071) RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 19286-0072 | 功能描述:手工工具 STOPPER HUSKIE #410H -01 HHLS (192860072) RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 19286-0075 | 功能描述:手工工具 SER-40 SCRAPER HUSKI E#51KD-02 (192860075 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。