参数资料
型号: 12216
厂商: NVE Corp/Sensor Products
文件页数: 128/145页
文件大小: 0K
描述: MAGNET 6MM DIA X 4 MM THICK
标准包装: 25
系列: *
其它名称: Q7078272B
Application Notes
The magnetic particles in the ink of most currencies, and also any magnetic stripes on the currency,
can be magnetized and demagnetized by an external field. With only the earth’s field present, the bill’s
magnetic properties can be seen. However, the signal increases when using an external field.
This external magnetic field can be set up in a few different orientations, either in a front/back biasing
configuration or positioned “upstream” of the sensor. The back biasing configuration typically consists
of an electro/permanent magnet glued to the under side of the sensor or to the under side of the PCB.
The magnet should be aligned to produce the minimum output from the sensor. The ferromagnetic
particles in the bill will magnetize and thus distort the field to produce a field in the sensitive direction
at the sensor. Front biasing works in much the same manner except in this case the source of external
field is coming from the other side of the bill.
Flux
Bill
AA002-02
Passive
mounting
4 leads, V+,V-
Out+, Out-
Magnet
Front biasing
Magnet
Back biasing
Positioning the magnet “upstream” from the sensor consists of magnetizing the bill before it reaches
the sensor—this terminology comes from an application where the bills are moving past the sensor on
a conveyer belt or rollers. With a magnet placed near the moving bill, the bill is magnetized before
passing the sensor. The application’s geometrical requirements, strength of magnet, as well as sensor-
bill distance will determine which configuration works the best in each application. The following are
some graphs that show the characteristics of back-biasing an AA002 sensor.
To determine the sensitivity of back biasing positioning, the magnet was moved along the sensors
sensitive axis. The goal was to position the magnet so that there is minimum field in the sensitive
direction. To obtain this, one pole of the magnet must be directly under the sensing resistors of the
bridge. Note the steep slope around the zero output, which makes exact positioning difficult.
- 128 -
www.nve.com phone: 952-829-9217 fax: 952-829-9189
相关PDF资料
PDF描述
123-5863-12-163 LED BASE MINI PNL IND OIL TIGHT
1230-100A-3L SENSOR PRES 100PSIA 0-50MV 8-DIP
124-1363-01-113 LED BASE PMI 11/16" SCREW TERM
1240-015D-3L SENSOR PRES 15PSID 0-50MV 8-DIP
125-1191-403 RED STOVEPIPE PMI CAP
相关代理商/技术参数
参数描述
12-216 制造商:GC Electronics 功能描述:NEEDLE NOSE PLIERS; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No ;RoHS Compliant: No 制造商:GC Electronics 功能描述:Needle Nose Pliers
122160 功能描述:RF 连接器 TNC ST BULKHEAD JACK 58-303 LMR195 RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型:
12-2160 制造商:GC Electronics 功能描述:REPLACEMENT TIP FOR 12-2157 制造商:GC Electronics 功能描述:TOOLS, DESOLDERING; For Use With:12-2157 Soldering Iron ;RoHS Compliant: Yes 制造商:GC Electronics 功能描述:Replacement Tips For 12-2157
1221-6001 功能描述:RF 连接器 SMP FML FLOAT MNT S/R .047 .093 PNL RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型:
122160-11 功能描述:TNC Connector Jack, Female Socket 50 Ohm Panel Mount, Bulkhead - Front Side Nut Solder 制造商:amphenol-rf division 系列:- 包装:散装 零件状态:有效 连接器样式:TNC 连接器类型:插孔,母形插口 触头端接:焊接 保护端接:压接 阻抗:50 欧姆 安装类型:面板安装,隔墙式(前端螺母) 电缆组:RG-58, 58A, 58B, 58C, 141, 303, LMR-195, Belden B7806A, 9907 紧固类型:有螺纹 频率 - 最大值:11GHz 特性:热缩管 外壳颜色:银 侵入防护:IP67 - 防尘,防水 基体材料:黄铜 基体表面:镍 中心触头材料:磷青铜 中心触头镀层:金 介电材料:聚四氟乙烯(PTFE) 额定电压:500V 工作温度:-65°C ~ 165°C 标准包装:100