- 您现在的位置：买卖IC网 > PDF目录18596 > 1-543382-1 (TE Connectivity)TOOL INSERT/EXTRACT TIP 25-KIT PDF资料下载
参数资料
| 型号： | 1-543382-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | TOOL INSERT/EXTRACT TIP 25-KIT |
| 标准包装： | 1 |
| 系列： | AMPLIMITE |
| 工具类型： | 插入/拔出工具 |
| 适用于相关产品： | D-Sub 端子 |
408-9404
i NOTE The wire must be positioned inside the wire slot of the
i NOTE Contacts with tail lengths longer than 10.85 mm [.427
2. Slide thumb over the wire toward the end of the
tip.
NOTE
tip.
3. Slide tip over contact wire barrel until the tip butts
against the contact shoulder.
4. Align contact with the BACK of the contact cavity.
Push contact straight into the contact cavity until the
contact bottoms.
5. Remove the insertion tool; then pull back on the
wire to ensure that the contact is locked into the
contact cavity.
4.2. Extracting A Wire Crimped Contact (Figure 4)
1. Position tool handle between thumb and
fingertips, and align contact wire with the wire slot
on the tip. Hold wire in this position with your thumb.
2. Slide your thumb over the wire toward the end of
the insertion tip.
3. Place tip over the contact post or crimp barrel and
slide the tip straight into the contact cavity until the
tip bottoms against the contact shoulder.
4. Holding the wire tight against the tool handle, pull
back on the tool handle to extract the contact. If you
experience difficulty in extracting the contact, repeat
Steps 1 through 4.
4.3. Inserting A Posted Contact (Figure 5)
1. Place the contact in the contact cavity. Do NOT
push on the contact post.
2. Position the tip over the contact post. Move the
tool along the post until the tip butts against the
contact stabilizer. Align the tip on the stabilizer as
shown in Figure 5.
3. Hold the tool handle, and push the contact post to
make certain that the contact is locked in the cavity.
NOTE
in.] must use yellow color coded insertion tips.
i NOTE The wire must be positioned inside the wire slot of the
NOTE
tip.
Back of Receptacle
Connector 205439-1 (Ref)
Wire
Slide Extraction Tip Over
Contact Post or Crimp
Barrel
Rev D
Wire
Slot
Extraction Handle
Figure 4
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| ASFLMPC-20.000MHZ-LY-T3 | OSC 20.000 MHZ CMOS MEMS SMD |
| 270X232A502B1A1 | POT 5K OHM 1/4W CARB LNR TPR |
| 270X232A252B1A1 | POT 2.5K OHM 1/4W CARB LNR TPR |
| ASFLMPC-24.000MHZ-LY-T3 | OSC 24.000 MHZ CMOS MEMS SMD |
| 270X232A503B1A1 | POT 50K OHM 1/4W CARB LNR TPR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 15433830 | 功能描述:汽车连接器 TPA MIC/P 064 LOCK RoHS:否 制造商:Amphenol SINE Systems 产品:Contacts 系列:ATP 位置数量: 型式:Female 安装风格: 端接类型: 触点电镀:Nickel |
| 15433830-A | 制造商:Delphi Corporation 功能描述:TPA 10F MICRO 64 |
| 1543391 | 功能描述:电缆组件 SAC-4P-M 8MS/20.0- 950/M 8FS RoHS:否 制造商:Molex 产品:Power Assemblies 类型:Cable Assembly 连接器端口 A:No Connector 连接器端口 A 管脚计数:4 连接器端口 B:No Connector 连接器端口 B 管脚计数: 型式:Male 线规 - 美国线规（AWG）:20, 28 长度:0.305 m 颜色:Black, Red |
| 1-5-433L | 功能描述:TAPE ALUM FOIL HIGH TEMP 1"X5YD RoHS:是 类别:胶带，粘合剂 >> 带 系列:433 MSDS 材料安全数据表:2393 MSDS 标准包装:40 系列:Scotch® 2393 胶带类型:屏蔽，高温 胶合剂:橡胶 背衬，载体:绉纸 厚度:0.0076"（7.6 mils，0.193mm） 厚度 - 胶合剂:- 厚度 - 背胶，载体，衬垫:- 宽:1.42"（36.00mm） 长度:180'（55.0m）60 码 颜色:棕褐 使用:喷漆，自动 温度范围:325°F（163°C）- 30 分钟 包装:- 其它名称:000212007130330212007130370006165651 |
| 15434 | 功能描述:印刷电路板和试验板 TERMINAL BOARD RoHS:否 制造商:3M Electronic Solutions Division 产品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 长度:0.1 in 宽度: |
发布紧急采购，3分钟左右您将得到回复。