- 您现在的位置：买卖IC网 > PDF目录19198 > 0638117500 (Molex Inc)TOOL HAND CRIMP .156 TERM RACHET PDF资料下载
参数资料
| 型号： | 0638117500 |
| 厂商： | Molex Inc |
| 文件页数： | 5/7页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP .156 TERM RACHET |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 5 |
| 系列： | PremiumGrade™, KK®, Trifurcon™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，18-24 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 189 (CN2011-ZH PDF) |
| 配用： | 0008560114-ND - KK 156 TERMINAL CRIMP HUMPBACK 0008520126-ND - KK 156 TERMINAL CRIMP 18-20 AWG 0008650129-ND - CONN TERM CRIMP 18-22 AWG GOLD 0008650128-ND - CONN TERM CRIMP 18-22 AWG GOLD 0008650119-ND - CONN TERM CRIMP 18-20 AWG GOLD 0008650118-ND - CONN TERM CRIMP 18-20 AWG GOLD 0008650114-ND - CONN TERM CRIMP 18-24 AWG GOLD 0008580136-ND - CONN TERM CRIMP 18-22 AWG GOLD 0008580135-ND - CONN TERM CRIMP 18-22 AWG GOLD 0008580118-ND - CONN TERM CRIMP 18-20 AWG GOLD 更多... |
| 相关产品： | WM4524-ND - LOCATOR ASSY FOR 63811-7500 GRAY WM4523-ND - LOCATOR ASSEMBLY |
| 其它名称： | 063811-7500 063811-7500-P 0638117500-P 63811-7500 63811-7500-P 638117500 638117500-P WM9010 |
Hand Crimp Tool for “KK ? ” .156 Center Terminals
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the hand tool.
3. Firmly press down on the brass pivot shaft with your thumb, while
pulling the locator up. Slip the locator off the top of the brass pivot
LUBRICATION POINTS
(BOTH SIDES) LIGHT OIL
(EVERY 3 MONTHS OR
5,000 CRIMPS)
shaft. See Figure 4.
4. Replace it with the desired locator by putting over the brass pivot
shaft and snapping it into place.
Figure 5
Maintenance
It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance
steps:
1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine
oil. Do not oil excessively. The tool was engineered for durability but like any fine piece of equipment it
needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil such as 30
weight automotive oil used at the oil points, every 5,000 crimps or 3 months, , shown in Figure 6 will
significantly enhance the tool life.
4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
certain terminations may affect the electrical characteristics of an application.
5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping
dies, and store the tool in a clean, dry area.
PRELOAD
Miscrimps or Jams
Should this tool ever become stuck or jammed in a
partially closed position, Do Not force the handles
open or closed. The tool will open easily by pressing
the ratchet release lever. See Figure 6.
SETTING WHEEL
ECCENTRIC AXLE
CHECK POINT
25.4MM
How to Adjust Tool Preload ( See Figure 6)
This hand tool is factory preset to 25-45 LBS. preload.
It may be necessary over the life of the tool to adjust
tool handle preload force. Listed below are the steps
required to adjust the crimping force of the hand tool to
WRENCH SET
(SOLD
SEPERATELY)
LOCKING
SCREW
HANDLE
GRIP
REMOVED
HANDLE
GRIP
RATCHET
RELEASE LEVER
Figure 6
obtain proper crimp conditions:
1. Remove or fold back the handle grip from the handle to expose the eccentric axle and setting wheel.
2. Remove the locking screw with a 2mm hex wrench. The wrench set (63810-0101), is not supplied. It is sold
separately from the hand tool.
3. Turn the eccentric axle and setting wheel with the wrench or pliers Counter-clockwise (CCW) to increase
handle force.
4. Replace the locking screw, aligning the nearest notch in the setting wheel to locking screw.
5. Replace the handle grip.
6. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted.
Doc No. ATS-638117500
Revision: C
Release Date: 12-06-06
Revision Date: 03-29-08
UNCONTROLLED COPY
Page 5 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 0638190900 | TOOL HAND CRIMP 16-24AWG |
| 0640160200 | TOOL CRIMP 16-28AWG MINI-FIT JR |
| 14319 | TOOL HAND CRIMP FOR SMB |
| PGR-6300-02-00-CTU | MPS W/DEVICENET CONTROL UNIT |
| PGR-6210-00 | GE RETRO RS-232 CIM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638117575 | 功能描述:LOCATOR ASSY FOR 63811-7500 GRAY RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:KK®, Trifurcon™ 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638117576 | 功能描述:LOCATOR ASSEMBLY RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:KK®, Trifurcon™ 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638117600 | 制造商:Molex 功能描述:HAND CRIMP TOOL 制造商:Molex 功能描述:CONN ACC HAND CRMP TOOL - Bulk 制造商:Molex 功能描述:MX150L HAND TOOL |
| 0638117675 | 制造商:Molex 功能描述:LOCATOR ASSEMBLY 制造商:Molex 功能描述:LOCATOR ASSEMBLY - Bulk |
| 0638117700 | 功能描述:HAND CRIMP TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:* 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
发布紧急采购，3分钟左右您将得到回复。