- 您现在的位置：买卖IC网 > PDF目录19029 > 0638100104 (Molex Inc)RETURN SPRING FOR 0638233900 PDF资料下载
参数资料
| 型号： | 0638100104 |
| 厂商： | Molex Inc |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | RETURN SPRING FOR 0638233900 |
| 标准包装： | 20 |
| 附件类型： | 弹簧 |
| 适用于相关产品： | 638233900 |
| 配用： | WM4576-ND - TOOL HAND CRIMP CRIMP TERM WM5152-ND - HAND CRIMP TOOL WM9026-ND - TOOL HAND CRIMP 16-24AWG WM9023-ND - TOOL HAND CRIMP 14-20AWG RATCHET |
| 其它名称： | 063810-0104 063810-0104-P 0638100104-P 63810-0104 63810-0104-P 638100104 638100104-P WM5144 |
Hand Crimp Tool for Splash Proof Crimp Terminal
2. While holding the locator button in, load the terminal into the proper
nest opening in the locator based on the wire gauge or terminal type
markings on the hand tooling. See Figure 3.
3. Release the locator button, allowing the locator to return to the crimping
position.
4. Close the tool handle until the first ratchet position engages. See
Figure 4.
5. Insert the properly stripped wire through the terminal and against the
wire stop. See Figure 5.
6. Crimp the terminal by squeezing the tool handles until the ratchet
TOOLING
PARTIALLY
CLOSED
PARTIALLY
CLOSE HANDLE
OPEN
POSITION
mechanism cycle has been completed. Release the handles to open
the jaws.
FIRST RATCHET
POSITION
Figure 4
TERMINAL
PRE-STRIPPED
WIRE
WIRE AGAINST
THE WIRE
STOP
WIRE
Figure 5
TERMINAL
WIRE STOP IS
PART OF THE
LOCATOR
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
7. Remove the crimped terminal from the terminal
locator by pulling on the wire.
8. Visually inspect the crimped terminal for proper
crimp location.
9. On some large O.D. wires, it may not be possible
to insert the wire with the tool partially closed.
Those wires should be inserted with the hand tool
in the open position. Insert the wire above the
terminal in the punch and against the wire stop
then close the tool. See Figure 6.
Note:
WIRE
WIRE STOP
Figure 6
TERMINAL
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers available, actual crimp height measurements may very slightly. An
occasional, destructive, pull force test should be performed to check hand tool crimp. Pull Force value Must
exceed the Minimum pull force specifications listed.
Doc No: ATS-638233900
Revision: A
Release Date: 06-18-10
Revision Date: 06-18-10
UNCONTROLLED COPY
Page 3 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 8097 | INCANDESCENT LAMP 3MM 12V 2 LEAD |
| CQM1-TC301 | 4 LOOP PT INPUT NPN OUT |
| 22 | LAMP MIDGET T-1 14V |
| 7132 | LAMP INCAND 3MM WIRE TERM 5V |
| 28MB | LAMP INCAND T-2.5 BAYO TELE 28V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638100105 | 功能描述:RATCHET SPRING FOR 0638233900 RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:- 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638101001 | 功能描述:SPRING 制造商:molex, llc 系列:* 零件状态:有效 标准包装:50 |
| 0638101050 | 制造商:Molex 功能描述:HAND TOOL FRAME - CS30 - Bulk |
| 0638101060 | 功能描述:HAND CRIMP FRAME 制造商:molex, llc 系列:* 零件状态:在售 标准包装:100 |
| 0638101100 | 功能描述:CS40 HIGH FORCE HAND CRIMP FRAME 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。